A concrete footing should be 100mm deep by 300mm wide if the footing is for a free standing wall. The footing should be increased to 150mm deep and 450mm wide if the wall being built is a retaining wall.
4 feet
Thereof, How many piers do I need for a 10×10 shed?
When in doubt always make it stronger! Increase to 12″ piers with 6×6 posts. Consider using 2×10 or 2×12 beams doubled or tripled on each row. Make sure that each beam span is no longer than 7′ if you are worried.
Also to know is, How deep should a concrete slab be for a shed? 4-Inch Slab Is Good for Most Sheds A 4-inch slab is generally a good thickness for a typical shed. This concrete floor can be poured in most locales on a 4-inch base of compacted gravel. That requires an excavation of at least 6 inches to make a slab that will be 2 inches above the surrounding ground.
Subsequently, question is, How many piers do I need? An 8 ft x 12 ft shed will need 6 piers, 3 per long side. Typically, the span between two piers is based on the dimensions of the beams and the joists. A double 2×8 beam should be supported every 4 to 6 feet.
Also, How do you level a concrete pier for a shed?
How far apart do piers need to be?
8 to 10 feet
How do you lay a concrete slab for a shed?
– Step 1: Mark the Location of the Shed. …
– Step 2: Dig Out the Foundation. …
– Step 3: Build the Concrete Form. …
– Step 4: Set the Form in Place and Level. …
– Step 5: Install Gravel to Achieve Uniform 4″ Depth. …
– Step 6: Install Reinforcing Bar. …
– Step 7: Mist the Gravel and Rebar with Water. …
– Step 8: Mix and Pour Concrete.
How deep should a concrete slab be?
Excavate the slab area to a depth of about 7 inches, allowing 3 inches for a gravel base and 4 inches for concrete.
How many piers does a house have?
Piling or Pier supports should be installed at each corner when an exterior wall changes direction. There should be a minimum of one piling support on every side of the corner piling. A masonry fireplace measuring two by five foot should be supported by 4 piers for a two story and 3 piers for a one story structure.
Can I build a shed on concrete blocks?
Size matters when considering shed foundation material. Small- to medium-sized sheds, up to 160 square feet, can rest on an on-grade foundation. The types of foundation for these sheds can include a gravel pad, paving blocks and lumber, solid concrete blocks and lumber, or deck blocks and lumber.
How many piers do I need for a shed?
An 8 ft x 12 ft shed will need 6 piers, 3 per long side. Typically, the span between two piers is based on the dimensions of the beams and the joists. A double 2×8 beam should be supported every 4 to 6 feet. A 2×8 joist can normally span 8 feet.
How do you level a concrete block for a shed?
Place the concrete blocks on pea gravel. Use the pea gravel to level your foundation. Blocks along the same floor joist should be a maximum of 72” apart. The spacing between blocks on different floor joists should be a maximum of 48” apart (See floor layout below).
How far apart should concrete piers be?
8 feet
What kind of foundation do I need for a shed?
The types of foundation for these sheds can include a gravel pad, paving blocks and lumber, solid concrete blocks and lumber, or deck blocks and lumber. Larger sheds, more than one story high or greater than 160 square feet, should avoid the on-grade foundation style for support.
What’s the best surface to put a shed on?
– Tanalised Timber Battens (or railway sleepers)
– A1BaseKIT or Pressure-Treated Frame.
– QuickJACK Metal Frame Supports.
– Timber Decking.
– Paving Slabs.
– Plastic Grid System.
– Concrete.
– Existing Hardstanding.
Can you put a shed on concrete?
Sheds can be built on the following type of foundations: Concrete floor. Concrete piers. Compacted gravel.
Can you put a shed straight onto concrete?
If your shed has bearers (pressure treated pieces of wood attached to the bottom of the shed), you can place your shed directly on concrete or paving slabs. The bearers will help protect the shed from moisture damage and create space for air circulation. The concrete or paving slabs must be level.
Don’t forget to share this post 
References and Further Readings :
