The Whirlpool Duet Dryer F01 error may be able to be fixed with a simple reset of the main control. Unplug the dryer for 1 minute and plug it back in this will reset the control if the error persists after that you will need to check the dryer thermal fuse. The fuse is located on top of the blower wheel housing.
Thereof, How do you change a bearing on a dryer?
Also to know is, How do you reset a Whirlpool dryer? If your Whirlpool dryer displays a “PF” error code, indicating a recent power failure, the dryer will need to be reset and restarted. This is done by pressing “Start” for a few seconds to restart the dryer. If the dryer does not restart automatically, select a new cycle and any options then press “Start” to begin.
Subsequently, question is, How do you change a bearing on a GE dryer?
Also, How do you run a diagnostic on a Whirlpool Duet dryer?
press and hold for three seconds, release for three seconds; press and hold for three seconds. You’ll know you’ve entered diagnostic mode because all the indicators on the console will light up for five seconds and you’ll see the code “88” in the Estimated Time Remaining display.
How do I run a diagnostic on my Whirlpool washer?
How do you replace the top bearing on a GE dryer?
How do I change a dryer bearing?
How do you lubricate bearings on a dryer?
Locate the rubber-rimmed rollers with roller bearings at the back of the drying casing. Squeeze two to three drops of oil on the front and back of each roller bearing. Lift the dryer drum and place it back on the rubber-rimmed rollers. Hold the drum with your knee.
How much does it cost to replace bearings in a dryer?
Part Material Cost Total Cost
—————- ————- ———-
Dryer thermostat $3-20 $180
Bearing $50 $130-$250
Roller $10-30 $90-$230
Timer $50-$70 $130-$270
How do I reset a Whirlpool dryer?
If your Whirlpool dryer displays a “PF” error code, indicating a recent power failure, the dryer will need to be reset and restarted. This is done by pressing “Start” for a few seconds to restart the dryer. If the dryer does not restart automatically, select a new cycle and any options then press “Start” to begin.
Can I use wd40 on my dryer?
NEVER spray any cleaning solution including WD-40 directly into the dryer as the residue may get into the drum holes and cause a serious fire hazard! … This is very important as WD-40 is flammable.
How do you reset a Whirlpool washing machine?
Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.
How do I run a diagnostic on my Whirlpool refrigerator?
To start with we need to start the refrigerator’s diagnostic mode. To do this open the refrigerator door and press one or both door switches, depending on your refrigerator type. Next press the refrigerator temperature (+) button three times in ten seconds and release the light switch or switches.
Why is my Whirlpool dryer not working?
The thermal fuse is the most common problem with Whirlpool dryers not running. The thermal fuse cuts the dryer off in the event it overheats. … So if your thermal fuse is bad you should check the vent. To check the thermal fuse, first unplug dryer and remove back.
How do I know if my dryer bearing is bad?
If those bearings are defective or run-down due to years of use, you’ll hear a squeaking or squealing noise as your dryer drum rotates. To test whether or not the bearings are malfunctioning, manually rotate the drum. If you feel any resistance or you hear squeaking, you’ll need to replace your drum bearings.
Is it worth fixing a dryer?
If a dryer is relatively new (five years or less), having it repaired can extend its life that much longer and save money in the long run. … It can be worth spending $150 – $200 to repair a midrange or high-end dryer that’s less than three years old, for example.
Don’t forget to share this post 
References and Further Readings :
