– Step 1 – Unplug and Clean. Always unplug your water cooler dispenser before doing any repair or maintenance on it. …
– Step 2 – Reset the Water Cooler. Drain any remaining water and wipe dry. …
– Step 3 – Make Replacements.
Thereof, Why is my water cooler not cold?
Water cooler troubleshooting Very often if your water cooler is not working, the problem can be traced to the power supply. So as a first step, check that it is properly plugged in at the wall and the mains power is turned on. If it is switched on but not dispensing water, the next step is to check your water supply.
Also to know is, Why is my water dispenser not working? The first, and most common reason is that your water tube in the door is frozen. … Another possible cause for this issue is a faulty water inlet valve. This valve opens the water supply to the dispenser; therefore, if the valve is defective or if the water pressure is too low, the water valve won’t open.
Subsequently, question is, Why is my water dispenser not cold? Check your freon levels if your water cooler is not providing you with cold water any longer. … Then turn the switches in the back of the cooler off. Unplug your water cooler, and leave it unplugged for 24 hours. When you do turn it back on, be sure to turn the back switches on as well.
Also, How do you troubleshoot a water cooler?
– Remove the water bottle.
– Drain the reservoir entirely by holding down both the cold and hot spigots.
– Place a fresh bottle on the water cooler.
– Watch for leaks. …
– Please place a large X on the faulty bottle and label it a leaker.
Is refrigerator water supposed to be cold?
The water reservoir for the in-door dispenser is usually in the refrigerator compartment behind the back wall. The water in that tank should be about the same temperature as food in the refrigerator compartment – if given a chance to cool properly.
Why did my water cooler stop working?
With bottom-filled water coolers, a common cause of flow issues is a poor connection of the hose between the probe head (on top of the bottle) and the water pump. Ensure that the hose is fully inserted into both. If yours is a mains-fed water cooler, ensure the mains tap is turned on.
Why is my refrigerator water not cold?
Make sure that the air flow around this tank or coil is not blocked with food items. This could prevent the water from cooling properly. Also, check your refrigerator temperature to make sure that it is cooling properly. A problem with refrigerator temperature could also prevent your dispenser water from being cool.
How do I make my water cooler colder?
How do I reset my water cooler?
To do a reset, drain a few cups of water out of both the hot and cold sides of the water cooler. Then turn the switches in the back of the cooler off. Unplug your water cooler, and leave it unplugged for 24 hours. When you do turn it back on, be sure to turn the back switches on as well.
Why is my water cooler not working?
With bottom-filled water coolers, a common cause of flow issues is a poor connection of the hose between the probe head (on top of the bottle) and the water pump. Ensure that the hose is fully inserted into both. If yours is a mains-fed water cooler, ensure the mains tap is turned on.
How do you troubleshoot a water dispenser?
– Straighten or Replace the Dispenser Tube. …
– Clean Out the Water Lines. …
– Inspect and/or Change the Water Filter. …
– Test the Water Pressure. …
– Defrost the Water Line. …
– Check the Pressure Switch. …
– Inspect for a Faulty Door Switch. …
– Replace the Control Board.
How do you unclog a refrigerator water line?
Unclog Refrigerator’s Water Dispenser Hose Find the water dispenser line and unscrew the screws holding it in place. Then hold the water button at the front of your fridge down to see if any water comes through. If it does, it’s likely there was an air clog in the line which should now be removed.
How long does it take for a water dispenser to work?
It may need to fill the water tank thats located in the refrigerator section. Push and Hold the water dispenser lever in while it fills that tank, it may take a minute or 2, then water should start flowing in the front, put a glass or cup there to catch the water.
How does a water dispenser cold water?
The cold water runs through two carbon activated filters, followed by a UV light chamber where it is purified. CO2 is added to the water if there is a sparkling water option on your water dispenser. It then dispenses the relevant option of cold or sparkling water.
How does a water dispenser cool water?
The refrigeration system is attached outside of the coil and the cold transfers through the pipe walls to chill the water in the coil through conduction. When the taps are operated, the chilled water is dispensed at mains pressure.
Why is my primo water cooler not cold?
Unplug the unit. After a few minutes, plug the unit back in, turn the switches back on and give it one hour and recheck the water temperature. If this does not correct the issue, please call our Customer Service Center. … Empty the cold reservoir by dispensing water from the cold tap at the front of the dispenser.
Don’t forget to share this post 
References and Further Readings :