Also asked, how do I know my fascia size? Multiply the 1-1/2 inch width of the fascia board by the slope of the roof (e.g. 4/12). 1.5” times 4 divided by 12 = 0.5 or ½ inch. For a 2×6 fascia board at a 4/12 slope, the trim size would be 1-1/2 inch x 5 inches for an overhang without a soffit.
You construct fascia boards out of 1-inch lumber. The width depends on the width of the rafters, but since builders generally use two-by-six or two-by-eight lumber for roof construction, the most common dimensions for fascia boards are one-by-six and one-by-eight inches.
Thereof, What type of board is used for fascia?
Wood is the most common material used to make fascia. Typically, wood fascia boards are made of spruce, pine or fir. However, cedar fascia boards (same wood for decks) are gaining steam.
Also to know is, Can I use pressure treated wood for fascia? It’ll last a long time if you have the proper detail on your home. But pressure treated lumber is not used for fascia boards.
Subsequently, question is, What size does fascia come in? The width depends on the width of the rafters, but since builders generally use two-by-six or two-by-eight lumber for roof construction, the most common dimensions for fascia boards are one-by-six and one-by-eight inches.
Also, What sizes do fascia boards come in?
You construct fascia boards out of 1-inch lumber. The width depends on the width of the rafters, but since builders generally use two-by-six or two-by-eight lumber for roof construction, the most common dimensions for fascia boards are one-by-six and one-by-eight inches.
How do you measure soffit and fascia?
Multiply the total length by the width to obtain the area of soffit needed to fill the gap. For example, if the total eaves length is 110 feet, and the width is 2 feet, multiply 110 by 2. The result, 220 in this example, is the number of square feet of soffit required.
What are fascia boards made of?
Fascia boards are made from structurally strong wood, which helps give support to the gutter, as well as to the soffit, which is installed just behind it. The fascia supports these sections of the home, and gives the gutter and gutter tiles something to attach onto.
What length does fascia come in?
The width depends on the width of the rafters, but since builders generally use two-by-six or two-by-eight lumber for roof construction, the most common dimensions for fascia boards are one-by-six and one-by-eight inches.
What are fascia boards?
The fascia board is the long, straight board that runs along the lower edge of the roof. The fascia is fixed directly to the lower ends of the roof trusses and usually does all the work of supporting the lower edge of the bottom row of tiles.
How do you measure and cut fascia?
– Start from a fascia piece’s left edge and measure 5 1/2 inches to the right. …
– Measure from the bottom of the F-channel (which is the hook piece on the bottom of the rafter face) to the undersill (the top of the rafter face). …
– Measure from the 5 1/2-inch piece of fascia’s bottom edge up.
What length does soffit come in?
12-ft.
What length does vinyl soffit come in?
12-ft.
How thick should fascia boards be?
3/4″
What is the best material for fascia boards?
– The most common choice due to its affordability.
– Primarily constructed from either spruce, pine, or fir.
– Because it is not water-resistant, wood is subject to rot.
– Must be primed and painted regularly to extend longevity.
What type of wood should be used for fascia?
Wood Is a Common Fascia Material Cedar is a popular fascia wood and redwood is another. That’s because both species resist rot and moisture very well, even when unpainted. If you prime and paint the fascia, you can also make them out of fir, spruce or pine, which are all less expensive.
What material is used for fascia boards?
Wood
How thick is a soffit board?
Standard soffit material is 3/8- or 1/2-inch-thick exterior plywood in pine (or similar softwoods) or cedar. Common, but much less durable, is Masonite or similar fiberboard soffit, as well as much more weather-resistant fiber-cement.
Don’t forget to share this post 
References and Further Readings :
