– Remove the furnace cover panel, which should expose the burner assembly and pilot. …
– If the pilot light is out, attempt to relight it.
– If the pilot light does not light or does not stay lit, then replace the thermocouple.
– If the pilot light is burning, examine its color.
Remove the front cover panel on your furnace or boiler. This should expose the pilot, which simply looks like a small single burner, kind of like a candle or if you only had a single flame lit on a gas stove. If there is no flame, then the pilot is out.
Thereof, How do you light the pilot on a Trane xr80?
Once the gas has had time to dissipate, turn the knob to “Pilot.” Then, hold down the “Reset” button and bring the flame of a long lighter close to the pilot light opening. This should light the furnace pilot light. Once you are sure the pilot light is on, release your pressure on the reset button.
Also to know is, How do I reset my Trane xr80 furnace? Wait until your furnace cools down before you attempt to reset the blower motor button. After the furnace cools, access the blower motor compartment. The compartment usually sits at the very bottom of the appliance. If you look inside the blower motor fan, you should find the reset button.
Subsequently, question is, Should the pilot light always be on in a gas furnace? If you have an older gas furnace, your heating unit relies on a little blue flame known as a pilot light to ensure ignition of the burners. Water heaters, gas fireplaces and old gas stoves also often have similar pilot lights. … Since the pilot light needs to remain active, your furnace is always consuming some gas.
Also, How can I reset my furnace?
– First, turn off the power supply to the furnace by turning off the breaker in the circuit box.
– Locate the reset button on the furnace and press it to reset the furnace. …
– If the button is popped up, press it down.
– Return the cover to the blower compartment and turn the power on.
Does Trane xr80 have a pilot light?
Trane xr80 pilot light. That is an Intell-ignition 50A65 control board and does not use a pilot light. It uses a hot surface igniter. … Although today’s standard electric furnace uses a hot surface ignition, older models often use an intermittent pilot to ignite heat.
How do I clean my Trane furnace?
How do you reset the pilot light on a furnace?
Once the gas has had time to dissipate, turn the knob to “Pilot.” Then, hold down the “Reset” button and bring the flame of a long lighter close to the pilot light opening. This should light the furnace pilot light. Once you are sure the pilot light is on, release your pressure on the reset button.
Should I hit the reset button on my furnace?
Don’t hit “reset” more than twice. The process pumps oil into the burner chamber, where it can accumulate if you have no ignition. Then when the furnace finally does start, it can do so explosively. So if the button won’t reset, or quickly pops up again, it’s time to call a professional repair service.
Does a Trane furnace have a pilot light?
A key component to any Trane furnace’s efficiency is the proper operation of the unit’s pilot light, which ignites the burners to heat a home when they’re signaled by the thermostat that the room temperature has dropped below the desired level.
Where is the filter on my Trane furnace?
Get to know your furnace The filter is located near the air return. The direction of air flow moves from the air return to the air supply, which you will want to remember when you insert your new filter.
When should a furnace be reset?
1. No Heat Coming Out. If your furnace doesn’t have any air coming out at all and the pilot light is out, it’s worth it to try resetting the furnace. If this doesn’t work, there may be a problem with the thermostat setting, the power, or the gas line.
What do you do when your pilot light goes out?
– Turn off your appliance at the power switch or thermostat.
– Find the gas valve control knob and turn it to select “pilot.”
– If pilot light controls are sticky, do not apply force or use oil. …
– Press the red button while simultaneously holding a match to the pilot burner.
Is there a reset button on a Bryant furnace?
Look for a small red or yellow button on the side of the blower motor. … Press the reset button down if it has popped up.
What MERV rating does Trane recommend?
MERV-13
How do you clean Trane CleanEffects?
Which way does the filter go in the furnace?
Slide the new filter in with the arrow pointing toward the furnace. Replacing your air filter is not difficult. Remember that air flows from your ducts, through the filter, and into the furnace. The arrow on the filter should always point toward the furnace.
Don’t forget to share this post 
References and Further Readings :
