Press the ‘7’ key and you will receive a number corresponding to the affected zone. The indicated zone is reading a low battery condition and needs a replacement battery. Replace the battery in the contact and the condition will clear.
A yellow triangle on your DSC ADT Alarm system is also known as a “trouble light.” That means if you see this symbol, your system has an issue that you need to resolve. A trouble light could mean 1 of 8 problems. To find out what the problem is, you can simply press *2 on your keypad.
Thereof, How do you clear the trouble light on a DSC alarm?
DSC alarms can go off for a number of reasons. To reset the alarm or the warning lights, enter your master code twice, press the reset button, and then enter “*72” if the alarm is still ringing.
Also to know is, How do I clear the memory on my DSC keypad? To clear the memory, arm and disarm the system. Certain sensors (such as smoke detectors and glass break detectors) have to be reset after an alarm. To reset detectors, press and hold the RESET key () for 2 seconds. If a sensor fails to reset, it may still be detecting an alarm condition.
Subsequently, question is, What does the trouble light mean on ADT alarm? A trouble signal (sometimes indicated in the alarm history by the abbreviation TR) indicates a possible problem or difficulty with your security system, such as a loose wire, a poorly aligned sensor or a low battery status.
Also, What does the yellow triangle mean on my alarm system?
The yellow triangle means that your alarm system is experiencing a trouble condition. This could be caused by a number of different possible factors, such as a low battery, an activated tamper or communication problems.
How do I bypass DSC zone?
– The System Must be disarmed prior to proceeding.
– Press the * Key.
– Press the 1 Key.
– Use the > key to scroll to the zone you wish to bypass.
– Press the * Key on the appropriate zone.
– A “B” should appear next to the zone when the system is bypassed.
How do I turn off the trouble light on my DSC alarm?
When a trouble is present the system trouble indicator light will illuminate and the keypad will beep every 10 seconds. To silence the trouble beep simply press the # key on the keypad. Now press *2 on your security keypad. The zones will light up indicating what troubles are present on the system.
How do I reset the yellow triangle on my DSC alarm?
Press the ‘7’ key and you will receive a number corresponding to the affected zone. The indicated zone is reading a low battery condition and needs a replacement battery. Replace the battery in the contact and the condition will clear.
How do I reset my DSC keypad?
– Open the access door on the unit.
– Press and hold the “RESET” key for 2 seconds.
– Press the buttons “*72” if the alarm does not reset after pressing the RESET button.
– Check the sensors if it still does not turn off.
Why does my DSC light stay on?
The Dynamic Stability Control (DSC) warning light may be simply a dirty or failed wheel speed sensor. I would recommend a Check Engine light… The following dashboard lights came up at the same time (ABS, TSC OFF, TSC/DSC). … DSC is your car’s “Dynamic Stability Control” which is a form of traction control.
Is it safe to drive with DSC light on?
You can drive a good 1000 mi or until you hear rumble or squeal sounds.
How do you test a DSC alarm?
– Press *6 Then Enter Your Master Code.
– Press 4.
– This will activate all keypad sounders, sirens and keypad lights for 2 seconds. …
– The Ready, Armed and Trouble Lights will flash for the duration of the test.
– Press # to Exit.
How do I turn off the trouble light on my ADT alarm?
A trouble light could mean 1 of 8 problems. To find out what the problem is, you can simply press *2 on your keypad. After pressing this on the keypad, your zone lights should light up, communicating any trouble areas. Pushing # will silence the trouble sound.
How do you troubleshoot a DSC alarm system?
How do I get my DSC alarm to stop beeping?
– 1) Go to any keypad and make sure the system is disarmed. If not, enter your disarm code as usual.
– 2) Enter the *2 which will indicate the trouble condition on most DSC keypads.
– 3) Press the “#” key three times. This will silence your DSC alarm system keypads.
Should I drive with traction control on or off?
Should I ever switch traction control off? We wouldn’t recommend turning traction control off during normal road driving – it doesn’t matter how good a driver you are, the traction control system can act to prevent a loss of control far faster than you are able to react behind the wheel.
How do I reset my alarm keypad?
You can reset your alarm system by powering it down and then powering it back on. This is what is known as a power reset. To power down the system, the backup battery must be disconnected, and the transformer must be unplugged. Then reconnect the battery and transformer to power it back on.
Don’t forget to share this post 
References and Further Readings :