– Shut off the power. Unplug the dryer. …
– Remove the lint screen. Pull the lint screen out of the housing in the top panel of the dryer. …
– Remove the lint screen housing screws. …
– Raise the cabinet top. …
– Disconnect the door switch wire harness. …
– Remove the door switch. …
– Install the new door switch. …
– Connect the wire harness.
If an electric or gas-heated clothes dryer continues to run after the door is open, the door safety switch is stuck in the closed position. To replace the switch, release the catches holding the dryer top down by slipping a putty knife between the top and front panel, and pushing the clips toward the rear of the dryer.
Thereof, Why won’t my dryer shut off when I open the door?
If the dryer stops only when you open the door, you’ll likely need to replace the electronic control board. If the dryer won’t turn off when you open the dryer door, the dryer door switch likely failed. Replace the door switch if it doesn’t accurately detect the door being open or closed.
Also to know is, How do you remove a dryer door switch?
Subsequently, question is, Why does my dryer keep running when I open the door? If an electric or gas-heated clothes dryer continues to run after the door is open, the door safety switch is stuck in the closed position. To replace the switch, release the catches holding the dryer top down by slipping a putty knife between the top and front panel, and pushing the clips toward the rear of the dryer.
Also, Why does my dryer timer not work?
The timer contacts control the dryer motor as well as the heat circuit and the timer motor itself. A defective timer motor or a defect in the timer’s electrical contacts can cause the timer motor to fail and the timer will need to be replaced.
How do you disconnect a dryer door switch?
– Shut off the power. Unplug the dryer. …
– Remove the lint screen. Pull the lint screen out of the housing in the top panel of the dryer. …
– Remove the lint screen housing screws. …
– Raise the cabinet top. …
– Disconnect the door switch wire harness. …
– Remove the door switch. …
– Install the new door switch. …
– Connect the wire harness.
Where is the door switch on a dryer?
Locate your dryer’s door switch. It will be located around the door opening in the front panel. You may be able to pop the switch out of place, or remove it by removing only a single screw. If you are unable to access your dryer’s door switch this way, you will have to remove the front panel of your dryer.
How do you fix a dryer that won’t stop running?
How do I test a dryer door with a multimeter?
How do I know if my dryer door switch is bad?
Faulty Switch When the switch is broken, it is unable to tell the control panel the door is shut, so the dryer will not turn on. The only way to tell if the switch is faulty is to take it out of the dryer and test it with a multimeter.
Where is door switch on dryer?
Locate your dryer’s door switch. It will be located around the door opening in the front panel. You may be able to pop the switch out of place, or remove it by removing only a single screw. If you are unable to access your dryer’s door switch this way, you will have to remove the front panel of your dryer.
How do you test a dryer door switch with a multimeter?
Where is the door switch on a Whirlpool dryer?
How do I know if my dryer timer is bad?
Clip or touch one probe to the terminal from which you removed the wire. Touch the other probe to one of the other terminals. You should get a reading of zero. If you get a high reading, then the timer motor is bad and it’s time to replace it.
How do you remove the wire from a dryer door?
Why doesn’t my dryer stop when I open the door?
The door switch only allows the dryer to run when the door is fully latched. So it’s possible that your dryer won’t stop tumbling because the signal that the door’s really open isn’t being sent. … Unplug the dryer, and use your multi-meter to check for continuity.
How do I test a door switch?
Don’t forget to share this post 
References and Further Readings :
