Check the water level to make sure it is not too low in the spa. Then make sure you do not have an air lock in the spa pump or spa heater causing the code. You can also try removing the spa filter, or replace with a new one to see if the error code goes away while the old filter is removed.
When the power light on the control panel of your spa is flashing, it means the high limit sensor has tripped. On most occasions, this is caused by poor water circulation due to dirty/clogged filters, air-locks, or a bad circulation pump.
Thereof, How do you fix the error code on a hot tub?
Check the water level to make sure it is not too low in the spa. Then make sure you do not have an air lock in the spa pump or spa heater causing the code. You can also try removing the spa filter, or replace with a new one to see if the error code goes away while the old filter is removed.
Also to know is, How do I know if my hot tub circuit board is bad? If you have no display on your topside control panel, check the cable for damage, following it right to where it plugs in, on the circuit board. Unplug it from the board and the low-speed pump will come on within 1 minute, on both systems. If that doesn’t happen, either the pump or the circuit board is bad.
Subsequently, question is, What does the code Ice mean on a hot tub? Actual water temperature is 20 degrees cooler than the set temperature. Ice Not an Error. Water temperature is below 55 degrees. Will go away once water becomes warmer.
Also, Is there a reset button on a hot tub?
There are generally two “hard resets” in hot tubs, the GFCI, and the high limit reset. The GFCI pops if there is any type of electrical short (such as water getting into the heating element, the reset on that can be in one of three places.
How do you diagnose a hot tub problem?
– Heater Failure. If the water in your spa isn’t as warm as it should it, it may be an indication of heater failure. …
– Clogged Filter. If water flow is poor and your jets don’t seem to be working as well as they should, you may have a clogged filter. …
– Air Lock. …
– Noisy Pump. …
– Tripped GFCI Breakers.
What does ICE mean on hot tub?
Freeze condition
Why is my hot tub not working?
The first step to take is to check the circuit breaker panel that your hot tub is hooked up to. … If this restores power to your tub temporarily before the breaker is tripped again, consult an electrician – the problem is likely with your breaker and not your spa. If this does not fix the problem, check the GFI switch.
Where is the reset button on a Hot Springs hot tub?
Similarly, where is the reset button on a Hot Springs hot tub? The reset button is located in the equipment compartment. Plug the spa back into the power source.
What does PR code mean on hot tub?
first actuated
How do I unlock my hot tub control panel?
To unlock the panel, while holding down the “Temperature” button (or the “Up” button if you do not have the “Temperature” button), gently press and release the “Light” button twice.
Why has my hot tub stopped working?
The first step to take is to check the circuit breaker panel that your hot tub is hooked up to. … If this restores power to your tub temporarily before the breaker is tripped again, consult an electrician – the problem is likely with your breaker and not your spa. If this does not fix the problem, check the GFI switch.
How do you fix the HL code on a hot tub?
– Turn the power off at the breaker for 15 seconds and then flip it back on. This will reset the HL reading.
– You will notice the display show some numbers. …
– If you see the HL come back within a day or so, this means that there is likely a problem with the probe or the motherboard.
How do I drain my infinity hot tub?
Locate drain hose near or around the equipment. Remove cap and attach garden hose. Open the back valve on hose bib to drain spa.
Do I need to drain my hot tub?
With average use, your hot tub should be drained and refilled about once every three or four months. … But remember, that implies that you and another person are using the hot tub every day of the week. If you’re not, then you can probably go longer without draining.
What does PR mean on Beachcomber hot tub?
Message Meaning
—————- ——————————————————————————————————-
Pr This happens when the hot tub unit is actuated for the first time; eventually it goes into priming mode
–F / –C Means unknown temperature.
Std/ St STANDARD Means hot tub unit is functioning in Standard Mode.
Ecn/ Ec ECONOMY Means hot tub unit is functioning in Economy mode.
How do I test my hot tub control panel?
Turn the power on and check if the hot tub heats up or starts to filter. The surest way to check if a control panel works is to use one you know is working and connect it to the circuit board.
Don’t forget to share this post 💖
References and Further Readings :
