– Shut down the spa at the breaker.
– Make sure there is no debris in the water that can get sucked into the pump.
– Take out all of the filter(s) and set them aside.
– Turn spa back on at the breaker with the filters out.
Error message Meaning
————- ———————————————————————————-
SP – F1 in.xm or in.xm2 Fuse F1 is blown. Fan, blower, circulation pump, fiber optic
SP – F2 in.xm or in.xm2 Fuse F2 is blown. Pump 2, Pump 3 or blower that is more than 5 amp
SP – F3 in.xm or in.xm2 Fuse F3 is blown. Pump 1
Thereof, What does PR code mean on hot tub?
first actuated
Also to know is, How do I fix error code e04 on a lazy spa? Remove the pump from the liner by placing the stopper caps on the inside over the debris screens. Take the spa pump off and place this in a cool area or inside. Once this has cooled down for 1 to 2 hours, reattach the pump to the liner and complete the full reset. This should resolve the issue with the error code.
Subsequently, question is, What does sed mean on a hot tub? Standard, Economy and Sleep
Also, How do I reset my hot tub control panel?
– Locate the spa’s high-limit reset. This is a red button found on many spa packs. …
– Press the high-limit reset button. …
– Turn on your spa and observe its operation. …
– Flip the breaker panel switch on or press the reset button on the GFCI outlet to restore power.
How do I reset my Gecko spa?
The system detects spa water temperature exceeding 112°F (44.4°) (overheat condition). Remove spa cover and let spa cool down. Add cold water and lower filter cycle. If the temperature cools down within normal limits the error will reset itself.
Why has my hot tub stopped working?
The first step to take is to check the circuit breaker panel that your hot tub is hooked up to. … If this restores power to your tub temporarily before the breaker is tripped again, consult an electrician – the problem is likely with your breaker and not your spa. If this does not fix the problem, check the GFI switch.
How do I unlock my hot tub control panel?
To unlock the panel, while holding down the “Temperature” button (or the “Up” button if you do not have the “Temperature” button), gently press and release the “Light” button twice.
What does the code Ice mean on a hot tub?
freeze protection
How do I fix error code e01 on a lazy spa?
Remove the pump from the spa liner by placing the stopper caps within the spa over the debris screens. (You will first need to remove the filter housing to place the stopper caps) Strike the pump firmly on the side. This should move the sensor into the correct positon Plug the spa back in and reset the pump.
Why does my hot tub keep blowing fuses?
These fuses may blow due to, loose incoming connections at the spa at the breaker or a bad connection in the holder. … This may be the reason for a blown fuse on the incoming legs of power. Shorts to ground are a real danger which should cause the GFCI breaker to trip most likely before a fuse would blow.
What does SL on a hot tub mean?
sleep mode
Do hot tubs have a reset button?
A spa heater has a high-limit reset button. A spa or hot tub provides a form of personal relaxation known as hydrotherapy. … A spa heater may need to be reset if it has tripped or stopped working. Using the high-limit reset switch and checking all breakers and GFCI outlets can reactivate the spa’s heater.
How do you check a hot tub fuse?
– Shut off all power to the spa at the breaker and spa pack.
– Set your Ohm meter to the 1K setting.
– Remove the fuse from the board or fuse housing.
– Place your meter leads on each end of the fuse.
– Compare readings to printed Ohms level.
How do I turn my spa lock off?
To turn off Spa Lock: Press and hold the OPTIONS hard button and the LIGHTS hard button at the same time for 3 seconds. The spa lock icon will turn off.
How do I fix error code e03 on a lazy spa?
This error code is visible if the ambient air temperature is too low outside. The spa pump will not run if the air temperature is below 4-6°c. Remove the pump from the spa by placing the stopper caps on the inside of the spa over the debris screens. Carry the spa pump indoors and place blanket or duvet around the pump.
How do you stop a fuse from blowing?
When a fuse or circuit breaker does blow, the first thing to do is unplug all lights and appliances in that circuit. Then turn the circuit breaker back on (or replace the fuse). If the fuse or circuit breaker blows again, there is a short in the wiring or in one of the switches or receptacles in that circuit.Mar 27, 1986
Don’t forget to share this post 💖
References and Further Readings :