Once the gas has had time to dissipate, turn the knob to “Pilot.” Then, hold down the “Reset” button and bring the flame of a long lighter close to the pilot light opening. This should light the furnace pilot light. Once you are sure the pilot light is on, release your pressure on the reset button.
Thereof, How do you adjust the pilot light on a gas heater?
– Locate the access plate on the front of your furnace, and unscrew the screws that are connecting the access plate to your furnace. …
– Observe the flame. …
– Turn that screw counter-clockwise, and the flame should grow. …
– Rotate the screw on the pilot light clockwise, and the size of the flame will decrease.
Also to know is, How do you light a gas heater on the wall?
Subsequently, question is, How do you fix a pilot light on a gas heater? Check the Thermocouple Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.
Also, How do I turn on my Williams gas wall heater?
– To turn on your gas heater, locate the knob for starting.
– Turn the knob to “Pilot,” and then push down on the “Ignite” button.
– Once the pilot light comes on, hold down the Ignite button for 10 to 15 seconds.
– Set the temperature on the wall heater to your desired heating level.
How Big Should the flame be on a pilot light?
A proper pilot flame should be blue with a yellow tip and should be strong enough to cover about 1/2 inch at the end of the thermocouple tip. If the flame is too strong and improperly adjusted, it will be blue but may be noisy and lift off the thermocouple, causing improper furnace operation.
Should the pilot light always be on in a gas heater?
If you have an older gas furnace, your heating unit relies on a little blue flame known as a pilot light to ensure ignition of the burners. Water heaters, gas fireplaces and old gas stoves also often have similar pilot lights. … Since the pilot light needs to remain active, your furnace is always consuming some gas.
Why does my gas heater not ignite?
The pilot light or ignition sensor is usually the most common issue when your furnace will not ignite. … Then, remove the front panel to find the ignitor or ignition sensor. This is typically located near the burners. If the sensor or ignitor is dirty, it will need to be cleaned.
Why will my propane heater not light?
If the thermocouple is too far from the flame, this can cause the pilot to go out and shut down the propane heater; you can fix this easily by moving the thermocouple closer to the flame. … If your propane heater sparks but will not light, the gas cylinder that supplies it may be empty or the gas may even be shut off.
Can a pilot light flame be adjusted?
Adjusting the Pilot Flame If the pilot flame is too small, you may be able to make it larger by turning the pilot adjustment screw on the valve control counterclockwise with a screwdriver to open it. … The cause of a weak flame may also be an obstruction in the pilot tube.
How do you know if you have a bad thermocouple?
If you can’t get the flame to light at all, and you’re sure the gas is on, there’s probably an obstruction in the pilot tube. If the flame lights and goes out when you release the gas control knob after holding it in for the recommended 20 to 30 seconds, that’s the sign of a thermocouple malfunction.
How do I turn on my Williams wall heater?
Should the pilot light always be on in a gas water heater?
The pilot should always be burning on your water heater. Sometimes the pilot flame is hard to see through the viewing window. To be sure if the pilot is on or off, you need to remove the access door and shield and look at the burner and pilot through the opening.
Is it dangerous if the pilot light goes out on furnace?
Can a Pilot Light Outage Be Dangerous? The worry here is that when a pilot goes out, the gas valve that supplies the fuel for the pilot flame could still be pumping gas. This can mean a buildup of gas, and when the pilot is relit or relights itself it could result in a very serious explosion.
Do I need to turn gas off if pilot light goes out?
If the pilot light goes out on a storage or instantaneous hot water heater, space heater or a ducted heater, you will not have a gas leak. This is because all modern gas appliances with pilot lights have a fail-safe device that closes off the gas to the appliance in the case when the pilot may go out.
Is it dangerous if your pilot light goes out?
Can a Pilot Light Outage Be Dangerous? The worry here is that when a pilot goes out, the gas valve that supplies the fuel for the pilot flame could still be pumping gas. This can mean a buildup of gas, and when the pilot is relit or relights itself it could result in a very serious explosion.
Should the pilot light always be on in a gas fireplace?
Electronic ignition is when the pilot light on a gas fireplace/insert/stove is only running when the fireplace is on, this means that the unit is likely to have a battery backup as well. A standing pilot is always on, always using a small amount of gas to run constantly unless the gas is physically turned off.
Don’t forget to share this post 💖
References and Further Readings :