Locate the three screws on the top rear edge of the control panel that secure the control panel to the rear of the washer. Remove the three screws with a Phillips screwdriver. Rotate the control console forward and unhook the tabs on the bottom of the control console from the holes in the top of the washer.
Thereof, How do you remove the pump from a Maytag washer?
Also to know is, How do you remove the front panel of a Maytag washer? Locate the two screws securing the bottom of the front panel to the sides of the washer. Remove the screws with a nut driver. Swing the bottom of the front panel toward you and pull down to disengage the top of the front panel from the top panel.
Subsequently, question is, How do you take apart a Maytag Centennial washing machine?
Also, How do you remove the engine from a Maytag washer?
How do I remove the lid from my Maytag Bravo washing machine?
Where is the pump on a Maytag washing machine?
The pump is located behind a small panel on the back, lower left side of my washer. It’s attached to the bottom frame with 3 screws. It has two hoses attached, each with one spring clamp. Lift one side of the washer and slip the drive belt off the pully.
How do you remove the back of a Maytag washing machine?
Locate the three screws on the top rear edge of the control panel that secure the control panel to the rear of the washer. Remove the three screws with a Phillips screwdriver. Rotate the control console forward and unhook the tabs on the bottom of the control console from the holes in the top of the washer.
How do I remove the front of my washing machine?
– Unplug the washer from the wall outlet.
– Locate 2 spring clips between top and front panel (Approximately 4 inches in from corners.)
– Insert putty knife between top and front panel and push in to release clips.
– Pull top of front panel forward, lift up and off bottom locating tabs.
How do you remove the front panel of a washing machine?
– Unplug the washer from the wall outlet.
– Locate 2 spring clips between top and front panel (Approximately 4 inches in from corners.)
– Insert putty knife between top and front panel and push in to release clips.
– Pull top of front panel forward, lift up and off bottom locating tabs.
How do you remove the back of a washing machine?
– Unplug the Whirlpool washer and turn off the water lines. …
– Locate the screws on either side of the washer console. …
– Slide the console toward the front of the machine. …
– Unplug the console from the top of the washer. …
– Remove the flat, wavy silver metal clips that connect the top of the washer cabinet to the rear panel.
How do you remove change from washing machine?
Take your pliers and squeeze both ends of the hose clamp, and then slide it down the hose away from the washtub. After you pull the drain hose from the washtub, shake the hose in order to remove any coins that have been trapped.
How do you take the top off a washing machine?
Open the lid on the washing machine and place your hand between the drum and the top of the machine. Lift upward and toward you to remove the metal cabinet. If the cabinet does not lift easily, slide it toward the front of the machine, then lift. Be careful not to dent the casing as you take it away from the drum.
How do I reset a Maytag Centennial washer?
– Unplug the washer for 1 minute from the electrical outlet.
– Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
– The motor has now been reset and is ready for you to start a cycle.
How do I know if my washing machine pump is bad?
Remove the drain hose by unscrewing the clamps holding it to the pump outlet. Look for blockages inside the hose. If you don’t see any, the pump may be blocked or faulty. To check it, you have to disconnect the belt connecting it to the drive motor.
How do you remove the front of a top load washer?
– Unplug the washer from the wall outlet.
– Locate 2 spring clips between top and front panel (Approximately 4 inches in from corners.)
– Insert putty knife between top and front panel and push in to release clips.
– Pull top of front panel forward, lift up and off bottom locating tabs.
How do you troubleshoot a Maytag washer?
– Washer won’t spin.
– Washer is making loud noise.
– Washer won’t agitate.
– Washer won’t drain.
– Washer vibrating or shaking.
– Washer fills slowly or will not fill at all.
– Washer leaking water.
– Washer won’t start.
Don’t forget to share this post 💖
References and Further Readings :
