The Tapcon drill bit that is used depends on the diameter of the Tapcon screw being installed. The 3/16” Tapcon requires the use of 5/32” diameter bit, and the 1/4” Tapcon requires a 3/16” diameter bit.
Thereof, What kind of drill bit is needed for concrete?
masonry bits
Also to know is, Do I need to pre drill for Tapcon screws? The hole must be drilled using a hammer drill with a carbide tipped bit meeting ANSI standards. A bit that meets ANSI standards will ensure that the hole diameter will meet the requirements of the Tapcon®.
Subsequently, question is, What size drill bit do you use for a 5/16 Tapcon? tapcon uses a 5/16-in. 1/2-in. tapcon uses a 7/16-in. bit.
Also, What size Tapcon should I use?
Tap Con Screw Hole Diameter The hole tolerance is critical and must be drilled using a hammer drill and a carbide tipped bit that meets ANSI standards. The 3/16” diameter tap con requires a 5/32” hole and a 1/4” tap con screw requires a 3/16” hole.
How deep should Tapcons be in concrete?
The minimum depth of embedment for the Tapcon screw is 1 inch, and the maximum embedment is 1-3/4 inch. The depth of the hole should be drilled to allow a minimum space at the bottom of the hole of 1/2 inch. The minimum depth of the hole equals 1 inch plus 1/2 inch or 1-1/2” inches.
In which material should you use a Tapcon screw?
concrete
Do I need a hammer drill for Tapcon screws?
The Tapcon drill bit must be used in a hammer drill, and the hammer drill must be set in the hammer and rotation mode. Hole tolerance is critical when installing Tapcon concrete screws. To produce the quality hole required, the Tapcon bit must be used in a rotary hammer drill.
How do I choose a drill bit for a screw?
Hold the shaft of the drill bit up in front of the screw. You should only be able to see the threads of the screw (and maybe a bit of the screw). If you can’t see the threads the drill bit is too big. If you can see too much of the screw, the bit is too small.
How much can Tapcons hold?
1,360 lbs. *A safety factor of 4:1 or 25% of ultimate pullout/shear value is generally accepted as a safe working load. 340 lbs.
When Can I drill into new concrete?
Let the concrete cure for at least 3 days before drilling. Waiting 7 days would be best before installing the anchors. Expansion anchors exert a great deal of outward force against the concrete and it takes at least 5-7 days for concrete to cure to 60% of its designed strength.
Do you pre drill for Tapcons?
Before a Tapcon masonry screw can be installed, a hole must be drilled into the masonry. Use a hammer drill to ensure that the hole has the proper tolerance. … The carbide bit diameter required for the 3/16” screw is 5/32”. For the 1/4” screw a 3/16” carbide tipped bit must be used.
How much weight can a 1/4 Tapcon hold?
Size Minimum Embedment Pull-Out (lbs.)
—– —————– —————
3/16” 1” 600
1/4” 1” 750
What type of drill is used for concrete?
Hammer Drill
How much weight can concrete anchors hold?
Masonry and concrete anchor types are considered light-duty, medium-duty or heavy-duty, based on how much weight they can support. Light-duty anchors are good for wall hangings that weigh up to 50 pounds. Medium-duty anchors are good for wall hangings that weigh up to 200 pounds.
Should a drill bit be the same size as a screw?
The drill bit should be the same size as the shaft of the screw without accounting for the threads. To do this, simply line up a screw side by side with the drill bit. If they’re the same size, then you’re good to go. You can also look for the measurements labeled on most bits and screws.
How do you drill a hole in concrete?
Start the drill at its lowest speed for better control. Drill forward with steady, light pressure; do not force the drill. Drill the guide hole to a depth of 1/8- to ¼-inch. Stop the drill, sweep or blow away the accumulated concrete dust and pull out the drill.
Don’t forget to share this post 
References and Further Readings :
