– Once you’ve centered the heater on the wall you can measure the wire lengths needed.
– Run 12-5 wire from the control panel to the bottom of the sauna heater.
– Connect the numbered wires #10, #11 and #12, neutral and ground in the sauna control box first, then make connects the heater’s junction box.
30-60 amp
Thereof, Does a sauna require a GFCI breaker?
The sauna must be hooked up to a “dedicated” 220-240 volt, 30-60 amp breaker and GFCI. … If the sauna is connected to a non-dedicated circuit, overloading will result in nuisance tripping which requires resetting of the breaker switch at the house electrical panel.
Also to know is, What size heater do I need for my sauna? As a general rule of thumb a sauna heater needs 1 Kw to heat 50 cubic foot of room space. This is a general rule and an outdoor sauna or a sauna built on outside walls may need to have the heater oversized. As an example a 6’x7’x7′ sauna room should require a 5 Kw heater. (252 cubic feet divide by 50 = 5.04).
Subsequently, question is, Where are GFCI breakers required? The NEC mandates GFCI protection in many areas of the home: bathrooms, garages, outdoor receptacles, crawl spaces, basements, kitchens and anything within six feet of a sink or water source.
Also, How much electricity does a 2 person sauna use?
Sauna size Typical energy requirement Approximate cost (c/hr)
———- ————————– ———————–
2-person 1600W 19.2
4-person 2200W 26.4
6-person 3000W 36
How much power does a sauna use?
Usually, your sauna seller will be able to help you estimate how much power your sauna will use per hour. As a rough calculation, a 1000W sauna will use around 1 kWh (1 kilowatt per hour) of electricity.
Are GFCI breakers required?
The National Electric Code (NEC) and all local building codes require GFCI (ground-fault circuit interrupter) protection for many outlet receptacles throughout the house and in outdoor locations. … This required protection can be provided either by a GFCI circuit breaker or GFCI receptacles.
How big is a 2 person sauna?
Product Dimensions 49 x 39 x 75 inches
——————————- ————————————————————————————
Item model number BSA2409
Customer Reviews 4.6 out of 5 stars 221 ratings 4.6 out of 5 stars
Best Sellers Rank #72,455 in Patio, Lawn & Garden (See Top 100 in Patio, Lawn & Garden) #133 in Saunas
Is Discontinued By Manufacturer No
Do all circuits need to be GFCI on outlets?
The National Electric Code (NEC) and all local building codes require GFCI (ground-fault circuit interrupter) protection for many outlet receptacles throughout the house and in outdoor locations. … This required protection can be provided either by a GFCI circuit breaker or GFCI receptacles.
How big is a two person sauna?
A good size for an average two or three person sauna is from 4′ x 6′ to 5′ x 7′. Depending on the number of users and the set-up, the sizes can go up to 12′ x 12′, while also one-person 3′ x 3′ saunas still work. Public saunas are usually at least 100 square feet in size.
How long does it take to heat a sauna?
30 to 45 minutes
Is it better to sauna in the morning or night?
Use a sauna the first thing in the morning or the last thing at night, says holistic physician Lawrence Wilson in “Sauna Therapy.” The sauna treatment will be more effective at those times because you are likely to feel most relaxed. The more one relaxes, Wilson says, the more you will sweat.
Is it OK to sauna twice a day?
In the end, if you go to the sauna daily, you shouldn’t take more than one session at once. Keep in mind that excessive sessions may cause the opposite effect and weaken your body. Also, it is essential to take a cold shower or to go to the fresh air between the two sessions because your body needs to cool down.
Do saunas use a lot of electricity?
How much electricity does a sauna use? … As a rough calculation, a 1000W sauna will use around 1 kWh (1 kilowatt per hour) of electricity. You can therefore calculate your costs by multiplying how much energy your sauna uses by how much your electric company charges you for 1 kilowatt per hour.
How big should a sauna be?
6 feet by 5 feet
How do you use a harvia sauna?
Be sure to let the sauna heat for at least one hour before using the sauna. To turn the heater on, turn the On|Off and Timer dial clockwise past the small “1” and then back to the large “1” until you hear a click. The sauna heater should now begin heating and will do so for one hour and then automatically shut off.
How many GFCI do you need per breaker?
There’s no limit. A standard GFCI will protect up to 20 amps, drawn from any combination of receptacles, either the built-in one or any number of additional ones connected to its load terminals.
Don’t forget to share this post 
References and Further Readings :
