The type of load in question will also determine how much weight a 2×6 can hold on edge. For example, a 2×4 lumber may hold a 4-cylinder engine comfortably but may not hold a bigger one. On the other end, a 2×6 can support a V8 engine of between 600 – 700 lbs.
Thereof, How far can you span a 2×6 on a pergola?
You also have to consider allowable span, based on the size of the pergola you’re building. A 12-foot span is much too long for a 2×6 board, for example. Not only will it look weak to the eye, but it will sag over time. Most builders use a minimum of 2×8 for the upper framing members, and that’s for a small pergola.
Also to know is, Is a 4×6 stronger than 2 2×6? A 4×6 joist is theoretically stronger than a doubled 2×6 joist because it’s 1/2″ thicker, but the actual strength depends upon the knots and other inherent weaknesses of any particular piece of lumber (#2 lumber can have some nasty spike knots or large not-so-tight round knots or wane).
Subsequently, question is, Are 2×6 strong enough for deck joists? 2×6 joists should only be used on ground-level decks that do not require, and will not provide for, any guards. … Most decking is not strong enough to support longer spans than 16″. Some builders reduce joist spacing to 12″ on center to strengthen the deck frame or to increase maximum allowable joist spans.
Also, How far can you span a double 2×6?
For instance, a double 2×12 beam can span 12 feet; a (2) 2×10 can span 10 feet and so on.
Is a 4×6 stronger than a 2×8?
The debate is: A 4×6 standing 4 wide and 6 high… Unless it comes a ways from the pith of the log it will be stronger if it comes from a “boxed heart” timber. … A good 2×8 will support as much as a 4×6.
How far can you span a double 2×6 header?
Header Size Maximum Span Number of Trimmers
———– ———— ——————
Double 2×6 4 ft., 0 in. One
Double 2×8 5 ft., 0 in. Two
Double 2×10 6 ft., 2 in. Two
Double 2×12 7 ft., 1 in. Two
How far can a 6×6 beam span for pergola?
I would have main beams of up to 10′ max; less if possible, certainly for anything up to 2″ x 6″ timber, ideally around 5′. The acceptable span does increase, however, the thicker and deeper the wood. The type of wood you use for your project makes a difference, too: some timbers are harder than others.
How far can a 2×6 span without support?
How far can a 2×6 Rafter span without support? The table states that 2 X 6 rafters spaced 16 inches on center (o.c) can span a maximum distance of 13 feet 5 inches. Another option are 2 X 8 rafters spaced 24 inches o.c.
Is 2 2×6 or 1 4×6 stronger?
A 4×6 joist is theoretically stronger than a doubled 2×6 joist because it’s 1/2″ thicker, but the actual strength depends upon the knots and other inherent weaknesses of any particular piece of lumber (#2 lumber can have some nasty spike knots or large not-so-tight round knots or wane).
How far can a double 2×6 span without support?
When supporting joists that span 12 feet with no overhang beyond the beam, a double ply beam can span in feet a value equal to its depth in inches. For instance, a double 2×12 beam can span 12 feet; a (2) 2×10 can span 10 feet and so on.
What is the maximum span for a 2×6 joist?
How much weight can a double 2×6 hold?
480 pounds
Are two 2×6 stronger than a 2×8?
In bending, a joist composed of two 2×6’s (true dimension 1.5 inches x 5.5 inches) are slightly stronger than a single 2×8 true dimensions 1.5 inches by 7.25 inches.
How far can 2×6 decking span?
24 inches
Can you use 2×6 for deck boards?
Wood decking is commonly available in 2×6 and 5/4 x 6 profiles. 5/4 x 6 is produced specifically for decking and is milled with a radius edge or bull nose. 2×6 is thicker and is stronger, but is also more expensive. Spacing between deck boards provide a few critical functions.
What is the maximum span for a 2×6 floor joist?
Don’t forget to share this post 
References and Further Readings :