The overhang is multiple meaning that the sheeting you would overhang some 3/4-1″ followed by a drip edge then if using shingles another 1″. If using metal w/o drip another 3/4-1″ past the wood sheeting. You would want to keep your completed overhang close to 1-1/2″ if using gutter.
Thereof, What is the soffit and fascia on a house?
The soffit is part of the overhang where your roof meets your siding. When rain or snow hits your roof, it runs down, and the overhang allows the water to flow away from your house. … The fascia is the attractive board along the side of the overhang and the roof that helps your roof appear finished.
Also to know is, How do you frame soffit and fascia?
Subsequently, question is, What is the purpose of soffit and fascia? They protect your home from structural damage. Without protection, this moisture penetration will result in mold, which will lead to rotting in your rafters and sheathing. Soffits and fascia fortify water entry points, thereby preventing damage to the frame of the house.
Also, How much does it cost to replace soffits and fascia?
Replacing your soffit generally costs about $20 to $30 a linear foot installed, while replacing your fascia costs about $15 to $25 a linear foot installed. Prices for the project depend on a number of factors, including the materials used and the size of your house.
What is fascia height?
The top edge of the fascia board should be secured to the rafters 25mm higher than the tile batten thickness. For example, a batten of 25mm thickness requires a 50mm distance between the top of the rafter and the top of the fascia board. This distance is known as the fascia height.
What is soffit and fascia boards for?
Purpose. Typically a soffit is used in the area beneath the eaves on the exterior of a house to close the space beneath the eave. The soffit extends from the side of the structure to the edge of the eave. Fascia is used to create a barrier between the edge of the roof and the outside.
What goes on first fascia or soffit?
For most siding projects you will have 2x horizontals which will be attached to the wall via nails. The lower edge will have an identical height as the fascia framing bottom edge (also known as the sub-fascia). … You will first want to nail your soffit onto the structure, and then take care of the fascia afterward.
Should I replace soffit and fascia?
Fascia and soffits are integral to the structure of a property. They protect the roof and keep water, condensation and damp out of the home. … While they tend to last for years, fascia and soffits do need replacing, so every homeowner eventually needs to recognise the signs of wear and tear.
How do I fix my soffit and fascia?
– Remove Shingle Mold. Pry the narrow shingle mold from the fascia using a flat bar. …
– Remove Rotted Fascia. Remove the rotted section of fascia. …
– Remove Old Soffit. Pull down to remove the old soffit. …
– Remove Rotted Rafter. …
– Attach Cleat. …
– Attach New Rafter. …
– Seal Replacement Soffit. …
– Attach Replacement Soffit.
How far should shingles overhang the roof?
Shingles should not extend more than 3/4” (19 mm) past the drip edge. If shingles overhang the edge of the roof by more than 3/4” (19 mm), then they are not supported and may crack and break off. In addition, the wind resistance at the roof edge may be compromised.
How much does it cost to replace soffits?
Replacing your soffit generally costs about $20 to $30 a linear foot installed, while replacing your fascia costs about $15 to $25 a linear foot installed. Prices for the project depend on a number of factors, including the materials used and the size of your house.
How do you fix overhang shingles?
How tall is a fascia?
You construct fascia boards out of 1-inch lumber. The width depends on the width of the rafters, but since builders generally use two-by-six or two-by-eight lumber for roof construction, the most common dimensions for fascia boards are one-by-six and one-by-eight inches.
How do you calculate fascia?
Multiply the 1-1/2 inch width of the fascia board by the slope of the roof (e.g. 4/12). 1.5” times 4 divided by 12 = 0.5 or ½ inch. For a 2×6 fascia board at a 4/12 slope, the trim size would be 1-1/2 inch x 5 inches for an overhang without a soffit.
Do gutter companies replace fascia?
If your home’s fascia is damaged, rotted, or missing completely, it is recommended that this is fixed. The Brothers that just do Gutters can repair your fascia with an aluminum fascia wrap, which comes in multiple sizes, or we can replace the fascia completely.
How much does it cost to install UPVC fascia boards?
The national average materials cost to install fascia boards is $1.72 per linear foot, with a range between $1.37 to $2.06. The total price for labor and materials per linear foot is $6.22, coming in between $4.90 to $7.54.7 days ago
Don’t forget to share this post 
References and Further Readings :