Each deck board should be fastened with two screws at each point where the board crosses a joist to ensure the stability and durability of your deck’s surface.
Decking boards span from joist to joist. If you use 5/4 decking, joists must be no farther apart than 16 inches. Decking made of 2x4s or 2x6s can span up to 24 inches.
Thereof, What is the actual thickness of a 5 4 deck board?
Nominal Size Rough Size Actual Size: Surfaced 2 Sides
———— ———- —————————–
5/4 inch 1 1/4 inch 1 1/16 inch (27 mm)
6/4 inch 1 1/2 inch 1 5/16 inch (33 mm)
8/4 inch 2 inches 1 3/4 inch (44 mm)
12/4 inch 3 inches 2 3/4 inch (70 mm)
Also to know is, What are the dimensions of a 5 4 deck board? Nominal Size Rough Size Actual Size: Surfaced 2 Sides
———— ———- —————————–
– 3/4 inch 9/16 inch (14 mm)
4/4 inch 1 inch 13/16 inch (21 mm)
5/4 inch 1 1/4 inch 1 1/16 inch (27 mm)
6/4 inch 1 1/2 inch 1 5/16 inch (33 mm)
Subsequently, question is, How thick do deck boards need to be? 16” on center = standard for residential applications. 24” on center = required for some commercial applications and commonly used for docks and boardwalks; made possible by increased deck board thickness.
Also, How do I calculate how much wood I need?
TIP: To calculate board feet: rough standard thickness X actual width X actual length divided by 144. Use the thickness of the material you intend to start with, not end with. For example, the 3/4″ top will start from 4/4 lumber. The legs will start from 6/4 lumber.
What size boards should I use for decking?
For the deck surface, you can use 2x4s, 2x6s, or 5/4x6s. The 5/4 decking (pronounced “five-quarter”), available in cedar and pressure-treated fir, is 1 inch thick and 5-1/2 inches wide with rounded edges that make for a splinter-free surface.
How do I figure out how much wood I need?
You can measure board feet by multiplying length x width x thickness in inches, and then dividing by 144. If ordering a large amount by board feet, just multiply the total board feet needed by the price per board foot for the total cost.
How long should screws be for 5 4 decking?
Decking: Fasten 5/4 decking with 21/2-inch coated screws or 12d ringshank or spiral nails.
Can I use 2×6 for deck boards?
Wood decking is commonly available in 2×6 and 5/4 x 6 profiles. 5/4 x 6 is produced specifically for decking and is milled with a radius edge or bull nose. 2×6 is thicker and is stronger, but is also more expensive. Spacing between deck boards provide a few critical functions.
How far can 5 4 decking span?
Decking Board Considerations Decking boards span from joist to joist. If you use 5/4 decking, joists must be no farther apart than 16 inches. Decking made of 2x4s or 2x6s can span up to 24 inches. If you will run decking at an angle, you might need to put the joists closer together.
How far can a 2×6 span without support?
How far can a 2×6 Rafter span without support? The table states that 2 X 6 rafters spaced 16 inches on center (o.c) can span a maximum distance of 13 feet 5 inches. Another option are 2 X 8 rafters spaced 24 inches o.c.
How far can a 6×6 span without support?
Each 6×6 beam only spans 12 feet, of which 2 of those feet are supported by a knee brace. So technically the beams only span 10ft.
How much lumber do I need for a 2000 square foot house?
16,000 board feet
How thick should decking boards be?
Decking Type Actual Thickness (inches) Suggested On Center Joist Spacing (inches)
————————- ————————- ——————————————
Thermally-Modified 5/4 1” 16”
Pressure Treated Pine 5/4 1” 16”
Western Red Cedar 5/4 1” 16”
Composite 5/4 1” 12”
What is the most common deck board size?
16-ft.
Should I Space 5 4 decking?
Double Joists Are Important Deck boards – no matter the thickness (5/4″ or 2″) should always be fastened on top of a DOUBLE joist so there is enough nailing edge on each decking board where they are butted.
How wide is a 5 4 deck board?
WeatherShield 5/4 in. x 6 in. x 16 ft.
Don’t forget to share this post 
References and Further Readings :
