Fasten DUROCK Brand Cement Board with 1-1/4 hot-dipped galvanized roofing nails or 1-1/4 DUROCK Brand Screws, spaced 8 o.c. in both directions, penetrating floor a minimum of 3/4.
Fasten HardieBacker sheets with proper nails or screws (as listed in ”Materials Required” in the backer installation instructions) every 8” around the perimeter and all supporting studs. Keep fasteners between 3/8” and 3/4” from sheet edges and 2” in from sheet corners.
Thereof, How far apart are screws in durock?
Fasten board to wood studs spaced at 406 mm (16″) o.c.1 with 32 mm (1-1/4″) CGC Durock Wood Screws or 38 mm (1-1/2″) hot-dipped galvanized roofing nails spaced 203 mm (8″) o.c. for walls, 152 mm (6″) o.c. for ceilings, using with the same spacing.
Also to know is, How far apart should screws be in cement board? Fasten HardieBacker cement board with specified nails or screws (as listed in “Materials Required”) every 8 in over the entire surface. Keep fasteners between 3/8 in and 3/4 in from board edges and 2 in from board corners.
Subsequently, question is, Do you nail or screw Hardie board? James Hardie prefers and recommends installation of HardiePlank® lap siding by the blind nailing technique, such that fasteners are hidden by the course above. Fasteners shall be installed between 1 in. and 3/4 in. from the top edge and no closer than 3/8 in.
Also, How do you hang Durock cement board?
Apply Type 1 organic adhesive with 5/32″ v-notched trowel, latex- fortified mortar with 1/4″ square-notched trowel. Comb out adhesive or mortar in straight, parallel rows (as shown below) and immediately cover with panel. Adhere panels to subfloor, one panel at a time. Secure panels while adhesive is still wet.
How often do you screw cement board?
every 8 in
How do you screw down Hardibacker board?
How do you screw down a durock?
How far apart should screws be in HardieBacker?
Screw the HardieBacker into the floor, using 1¼-inch backerboard screws and using one screw every 8 inches. Offset the interior screws so they are staggered with the outer screws, and make sure no screws are closer than two inches from the edge.
How do you screw down cement board?
What kind of screws do you use for durock?
C. DUROCK Steel Screws, 32 mm (1-1/4) long, are used for applying 12.7 mm (1/2) DUROCK Cement Board to walls or ceilings. D. DUROCK Steel Screws, 42 mm (1-5/8) long, are used for applying 15.9 mm (5/8) DUROCK Cement Board to walls or ceilings.
How do you secure cement board to concrete?
To install CBUs, they must be attached to the substrate with nails, screws or staples every four to eight inches in both directions. Ceramic and stone tile installations require the backer boards to be installed into a bed of thinset mortar at the same time.
What size notched trowel for durock?
mortar or dry-set mortar mixed with latex additive that is suitable for bonding cement backer board to plywood subfloor, with 1/4″ square-notched trowel for mortar, 5/32″ V-notched trowel for Type 1 organic adhesive. Place cement board with joints staggered from subfloor joints.
Does it matter which side of Hardibacker faces out?
Cement board has a smooth side and a rough side. Face the rough side out if you will be using thin-set mortar adhesive to install the tile but the smooth side out if you will be using latex mastic.
How do you screw down concrete backer board?
How often do you screw backer board?
every 8″
How far apart are cement board screws?
Fasten HardieBacker cement board with specified nails or screws (as listed in “Materials Required”) every 8 in over the entire surface. Keep fasteners between 3/8 in and 3/4 in from board edges and 2 in from board corners.
Don’t forget to share this post 
References and Further Readings :