In newer houses especially, a drywall ceiling is about the same or cheaper compared to a suspended ceiling. … Because the real cost of drywalling a ceiling in a basement deals is in framing around the pipes and wires that were installed below the joists.
Walls in rooms with suspended ceilings are known as partitions because they don’t bear the load of ceiling joists or trusses. With certain fire codes, a partition extends above the height of the ceiling, and a metal wall angle attaches to the face of the partition at ceiling height.
Thereof, Can you use a stud finder on the ceiling?
Stud finders measure density to find beams, so they don’t work on popcorn ceilings. If your nail penetrates the ceiling and doesn’t hit a solid surface, check again an inch away; if you don’t find one there either, measure 24 inches in from the wall and check there instead.
Also to know is, How do I put a wall between ceiling joists?
Subsequently, question is, How do ceiling joists attach to top plate? To properly attach a ceiling joist to a top plate is a lot easier than you may think. Simply put, several nails have to be toenailed through the joist to keep it in place. Where the beam and joist meet on top of a wall is the only place a ceiling joist should hang.
Also, How do you attach rafters to top plate?
You may not be able to nail through the top plate into the rafter. But you can drive a screw through it. TimberLOK 6-inch long screws secure your rafter to the top plate by driving a screw at an angle from the joint between the wall stud and top plate, through the top plate and into the rafter.
Do ceiling joists need hangers?
You will need joist hangars if you are not bearing on 1-1/2″ of wood or 2″ of masonry. This is a typical setup to level a ceiling and common to see joist hangars nailed in place.
What is the point of a drop ceiling?
Modern dropped ceilings were initially created to hide the building infrastructure, including piping, wiring, and/or ductwork, by creating a plenum space above the dropped ceiling, while allowing access for repairs and inspections. Drop ceilings may also be used to hide problems, such as structural damage.
How much height do you lose with a drop ceiling?
Therefore, at minimum, you need 3-4” of clearance. That is as little as a ONE INCH difference in headroom loss compared to drywall (in my example).
How do you install roof rafters?
What can I put on my ceiling instead of drywall?
While more expensive, ceiling planks are an elegant choice for your new ceiling. These planks are available in a wide array of widths, colors, and wood grain patterns. Planks often give you the option of tongue-and-groove installation and may also be surface mounted on existing ceilings.
How do you figure roof rafters?
How do you calculate Birdmouth rafters?
– Divide the width of building by 2 e.g. 72 inches wide divided by 2 = 36 inches.
– Subtract half the width of the ridge board/beam – in this case, 0.5 inches.
How much does it cost to replace a drop ceiling with drywall?
At $5 to $28 per square foot, drop ceilings are more expensive to install than drywall. Installing drywall costs $1 to $3 per square foot but that does not include painting prices, which are $2 to $6 for each square foot.
Can you screw into ceiling joists?
The most secure way to hang objects from drywall is to screw a hanger into the wall or ceiling framing; a variety of wall anchors are available for hanging moderately heavy objects between studs or ceiling joists.
How much weight can I hang from a ceiling joist?
Regular garage ceiling joists of modern construction can generally support 50lb/sqft. If you have trusses or your joists are supporting more than just sheetrock or your garage is older this number could be significantly…
Which way do ceiling joists run?
An important thing to know about joists is that they usually run in the same direction throughout a house. If the visible joists in a basement or attic run east to west, for example, you can be fairly certain the invisible joists under the bedroom floor also run east to west.Aug 2, 1986
What is the minimum height for drop ceiling?
Requirements vary, but most codes stipulate a minimum 7 1/2-ft. ceiling height in new construction. Some codes, however, will accommodate a lower ceiling height if it’s part of a renovation project, so it pays to ask. You’ll need roughly 4 in.
Don’t forget to share this post 💖
References and Further Readings :
