Double Joists Are Important Deck boards – no matter the thickness (5/4″ or 2″) should always be fastened on top of a DOUBLE joist so there is enough nailing edge on each decking board where they are butted.
Getting Into Board Thickness… Decking boards come in varying thicknesses that can be a bit confusing. There is a nominal thickness and then an actual thickness. The most popular thickness for decking boards in North America is a 5/4 thickness which is an actual 1” thick.
Thereof, What size are pressure treated deck boards?
x 6 in. x 16 ft. Pressure-Treated Decking Board is ideal for aboveground projects where lumber is exposed to the elements. It is Pressure-Treated to help protect against rot, decay and termites.
Also to know is, Do you screw deck boards to every joist? Most deck boards are relatively straight and easy to lay, but there are always a few that need a little extra coaxing. Start on one end of bent boards and straighten them as you nail or screw them to each consecutive joist. Position the board so it bends away from installing decking.
Subsequently, question is, Why do they call deck boards 5 4? It simply refers to how many 1/4-inches thick the rough stock is. For example, 4/4 (read out loud as four-quarters) is 1-in. thick in the rough. 5/4 is 1-1/4-in.
Also, How many hidden fasteners do I need?
Q: How many do I need? A: To find the approximate number of fasteners needed for your deck simply multiply the number of decking boards times the number of support joists. Divide by 90 to get the number of boxes then round up to the next even pack.
What is the spacing for decking?
Overall, conventional decking profiles should be installed such that when seasoned, will have gaps between 1/8 and 1/4 of an inch. Look at the ends of the boards and install the decking “barkside” up to prevent cupping.
What is the standard size for deck boards?
Width: Six-inch wide boards are ideal in most cases. Four inch wide material takes longer to install, creates more gaps and requires a lot more fasteners—but you can use it. Eight inch wide boards, because of their greater width, have more of a tendency to crack and cup; avoid using them.
How far can you span 5 4 deck boards?
Decking boards span from joist to joist. If you use 5/4 decking, joists must be no farther apart than 16 inches. Decking made of 2x4s or 2x6s can span up to 24 inches.
How much do treated deck boards cost?
Material / Labor PT Lumber Cost Per Square Foot
—————- ——————————
Material $5.75 to $12.50
Labor $5.25 to $10.00
Do I need to use pressure treated wood for a deck?
This is why non-pressure treated wood is still required for use indoors, and why builders recommended that you only use pressure treated lumber for the support structure of a deck and switch to untreated wood for the surface. Any location where pets and kids spend time regularly should be built with non-treated wood.
How do you fix deck spacing?
What is the actual thickness of a 5 4 deck board?
Nominal Size Rough Size Actual Size: Surfaced 2 Sides
———— ———- —————————–
5/4 inch 1 1/4 inch 1 1/16 inch (27 mm)
6/4 inch 1 1/2 inch 1 5/16 inch (33 mm)
8/4 inch 2 inches 1 3/4 inch (44 mm)
12/4 inch 3 inches 2 3/4 inch (70 mm)
What size boards should I use for decking?
For the deck surface, you can use 2x4s, 2x6s, or 5/4x6s. The 5/4 decking (pronounced “five-quarter”), available in cedar and pressure-treated fir, is 1 inch thick and 5-1/2 inches wide with rounded edges that make for a splinter-free surface.
Can I use 2×6 for deck boards?
Wood decking is commonly available in 2×6 and 5/4 x 6 profiles. 5/4 x 6 is produced specifically for decking and is milled with a radius edge or bull nose. 2×6 is thicker and is stronger, but is also more expensive. Spacing between deck boards provide a few critical functions.
Where do screws go on decking boards?
No matter what kind of screws you use, always remember to place your boards with the bark side up. Boards can cup away from the bark side which will enable the water to run off the boards. Pre-drill the ends of the boards to avoid splitting using two screws where each decking board and joist intersect.
Do I need pressure treated wood?
Pressure-treated wood is required whenever you attach framing lumber or furring strips directly to concrete or other exterior masonry walls below grade. Note that this requirement is only for exterior walls, as these may wick moisture onto the lumber.
How many fasteners do I need for composite decking?
The general rule of thumb for standard deck fasteners is 350 screws for every 100 square feet of decking, which is based on standard 6” wide boards (5-1/2” actual), and 16” joist spacing.
Don’t forget to share this post 
References and Further Readings :
