Wire cutters are commonly used to cut copper, brass, iron, aluminum, and steel wire. Some wire cutters have insulated handles which ensure that you will not get shocked from the wires you’re working with. Diagonal cutters have intersecting jaws that cut the wire at an angle, leaving a flat tip.
Diagonal pliers (or wire cutters or diagonal cutting pliers or diagonal cutters or side cutting pliers) are pliers intended for the cutting of wire (they are generally not used to grab or turn anything).
Thereof, Why do they call side cutters dikes?
Dikes (another name for general-purpose wire cutters), most likely derives its nickname from a blend of the term “diagonal cutters.” Also known as “side cutters” and “diags,” these handy pliers have been an electrician’s best friend and led to an even more provocative idiom: “When in doubt, dike it out.”Oct 14, 2014
Also to know is, What do you use to cut metal wire? – Use diagonal cutters to cut electrical wires up to a certain gauge. …
– Use end nippers instead of diagonal cutters when it comes time to cut staples and nails. …
– The jaws of wire rope cutters pull the wire rope into them and trap the cable so that the ends cannot spread. …
– Use bolt cutters to cut off locks.
Subsequently, question is, Which of the following types of wire cutters would allow a worker to cut a heavy piece of wire using the least force? Shear cutters require the least force of all side-cutters to cut, and they make the smoothest cut possible.
Also, Which tool is used to cut wires?
Diagonal pliers
What are adjustable pliers used for?
Adjustable or slip-joint pliers offer two or more widths to accommodate a wider range of tasks. Handles are used to grip the pliers, a pivot allows the jaws to open and the head grips or cuts the material you are working with.
How do you cut wires without tools?
What are side cutters used for?
Side cutters are used on wire and the leads of electronic components, as well as to strip insulation.
How do you cut metal wire?
– Use diagonal cutters to cut electrical wires up to a certain gauge. …
– Use end nippers instead of diagonal cutters when it comes time to cut staples and nails. …
– The jaws of wire rope cutters pull the wire rope into them and trap the cable so that the ends cannot spread. …
– Use bolt cutters to cut off locks.
How many types of pliers are there?
five types
What do I use to cut a metal rod?
– Tubing Cutter. A tubing cutter is attached to the rod at the point where the cut is to be made. …
– Hacksaw. Use a hacksaw with a metal-cutting blade. …
– Abrasive Powered Metal-Cutting Blade. An abrasive metal-cutting blade mounted on a circular saw, a table saw or a miter saw makes a precise and thorough cut.
Which wire cutters are the best?
– Editor’s Pick: Knipex Diagonal Cutters.
– Hakko Micro or “Shear” Cutters.
– Klein Tools Side Cutters.
– Knipex End Cutters.
– Knipex Insulated Cutters.
– IRWIN Needle-Nose Cutters.
– BikeMaster Safety (or Locking) Wire Pliers/Cutters.
– Klein Tools’ Wire-Stripping Pliers.
How do you cut metal wire without a wire cutter?
It’s possible to use a hacksaw to cut wire if no cutter is available. You’ll want to use a blade with a high teeth-per-inch (TPI) count for as clean a cut as possible. Regardless of the TPI count, using a hacksaw to cut wire is difficult unless the wire has a large diameter.
How do you cut a metal rod at home?
Cut Metal with Your Circular Saw It may not be an obvious choice, but fitted with the right blade, a circular saw is a great metal-cutting tool. In our test, it cut through rebar like a hot knife through butter. You can cut mild steel up to about 3/8 in. thick using a ferrous-metal-cutting blade.
How do you cut wire without a wire cutter?
It’s possible to use a hacksaw to cut wire if no cutter is available. You’ll want to use a blade with a high teeth-per-inch (TPI) count for as clean a cut as possible. Regardless of the TPI count, using a hacksaw to cut wire is difficult unless the wire has a large diameter.
Are pliers and wire cutters the same thing?
What are common types of pliers and wire cutters? Pliers are made in various shapes and sizes and for many uses. Some are used for gripping something round like a pipe or rod, some are used for twisting wires, and others are designed to be used for a combination of tasks including cutting wire.
What do you use to cut a metal pole?
– Fit your saw with a carbide blade. Carbide is an extremely hard material mixed into metal saw blades to allow them to cut steel and other metals. …
– Mark a line for your cut using a chisel or the edge of a saw blade.
– Secure the pole. …
– Cut the pole. …
– Smooth the cut edges.
Don’t forget to share this post 
References and Further Readings :
