Keyhole The hole into which the key enters to operate the lock or latch. It is often referred to as the keyway, particularly in a cylinder mechanism.
Thereof, What is the inside of a lock called?
The cylinder, or lock body, is the part of the door lock where you insert the key. When it’s locked, the cylinder engages a series of spring-loaded pins which keep the cylinder from turning. When you insert a key, the uneven edge pushes the pins upward to fit the key’s height in that location within the lock body.
Also to know is, What are parts of a key called? A typical key is a small piece of metal consisting of two parts: the bit or blade, which slides into the keyway of the lock and distinguishes between different keys, and the bow, which is left protruding so that torque can be applied by the user.
Subsequently, question is, How does the inside of a lock work? Basic pin-and-tumbler locks have several spring-loaded pins inside a series of small cylinders. When the right key slides into a pin-and-tumbler lock, the pointed teeth and notches on the blade of the key allow the spring-loaded pins to move up and down until they line up with a track called the shear line.
Also, What are door lock parts called?
The main parts of a door lock are the cylinder, bolt, box and strike plate. It’s useful for any DIY-er to know how things around the home operate.
What are the parts of a door handle called?
– Knobs and Levers. The most obviously noticeable part of the door handle is the knob or level that actually allows for the door to open. …
– The Latch Mechanism. Perhaps the most important of all door handle parts is the latch mechanism. …
– Strike Plates and Boxes. …
– Door Knob Lock.
What is the inside of a door lock called?
The lock body, or lock cylinder, is the core of a door lock. The lock body turns to engage or disengage the lock’s bolt or latch when the appropriate key is used. In a mechanical lock, the lock body uses a series of spring-loaded pins to allow or stop the turning.
How do locks work?
When the right key slides into a pin-and-tumbler lock, the pointed teeth and notches on the blade of the key allow the spring-loaded pins to move up and down until they line up with a track called the shear line. When the pins align with the shear line, the cylinder can turn and the lock will open.
How does a lock and dam work?
At the point where bodies of water at different levels meet, a dam and lock system bridges the gap by creating a contained area that can individually raise or lower its own water level to step a boat up or down the waterway.
How does a lock look inside?
From the outside, they look much like any other lock. Inside, they they have curved, jutting out pieces of metal fitted inside them (called wards) that exactly line up with the holes in a particular key. Other keys can be inserted into the lock but the wards will stop them from turning.
How does a barge go through a lock?
Actually the first section of barges is electrically winched out of the lock chamber and is tied to the seawall outside the lock until the balance of the barges and tug is locked through. then they recable the whole works and procede to the next lock and dam to repeat the entire process.
What are the components of a door lock?
– Trim: Sometimes called a rose, the trim is a decorative plate attached to the door under the knob or lever. …
– Deadbolt: …
– Escutcheon: …
– Faceplate. …
– Backplate: …
– Latch bolt: …
– Spindle: …
– Strike plate:
What is a Long Key called?
Rattlesnake Key
How does a boat go through a lock?
Locks operate on a simple premise. You drive your boat into a chamber with gates at each end. To raise the boat, water is let into the chamber until it is even with the level of the water to be entered. When the water reaches that level the gates on the new elevation side are opened and you drive out.
How does a locker lock work?
Here’s how to do it: To open your locker, first, turn the dial to the right 2 or more revolutions and stop at the first number. Next, turn the dial to the left 1 full turn, passing the first full number and stopping at the second number. … Close the door and spin the dial to lock your locker.
How does a lock in a canal work?
For a boat to go up through a canal lock, the following sequence occurs: The bottom sluices are opened to allow the lock to drain. The lower gates can then be opened. … The lock is filled (if it is not already), the boat enters the lock which then drains, allowing the boat to exit on the lower level.
Are canal locks dangerous?
Canal locks are often such a fantastic a focal point of the UK’s inland waterway system, but unfortunately they’re also the most dangerous aspect of inland waterway navigation. … Locks are inevitably incredibly deep when full, therefore any non-swimmers and/ or children should wear life-jackets.
Don’t forget to share this post 
References and Further Readings :
