If F9 E1 (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water.
Whirlpool Duet Washer Error Code E01 F09 means LONG DRAIN TIME. When your Whirlpool washer goes into drain mode and the drain time is past 8 minutes and not reaching the reset level in the pressure sensor then the valves in the drain are turned off and the drain pump will cease to pump out the water.
Thereof, How do you clear the error code on a Whirlpool Duet washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
Also to know is, What does SD mean on a Whirlpool Duet washer? The Sd error means that the pressure switch has too much pressure on it during the drain and spin phase of the cycle which means there are too many suds in the wash tub. This error is mostly caused by using to much liquid detergent.
Subsequently, question is, What does f09 mean on a washing machine? LONG DRAIN TIME
Also, How do you reset a front load washer?
– Press POWER to turn the washer off.
– Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
– With the power disabled, press and hold the START/PAUSE button for 5 seconds.
– Plug the washer back in, or turn the circuit breaker back on.
How do you clear the error code on a Maytag washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do you clear the f11 code on a Whirlpool Duet washer?
To Fix Whirlpool Duet Washer F11 Error Code the first thing you need to do is check the wiring and connection between the central control unit and the motor control unit. Disconnect the wire at the central control unit from the motor control.
How do you clear the code on a Whirlpool Duet washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do I clean my Whirlpool Duet washer?
– Mix 3/4 cup liquid chlorine bleach with 1 gallon warm water.
– Open the door of the Whirlpool Duet washer and look for stains on the gray seal located just inside the machine. …
– Wipe the seal with a clean, dry cloth and leave the door open until the seal is completely dry.
– Mix a small amount of dish soap in warm water.
What does SD mean on my Whirlpool washer?
excessive detergent suds
How do I clear the error code on my Whirlpool washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
Is there a reset button on a washing machine?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
Can you reset a Maytag washing machine?
Plug the washer back in and lift and lower the lid 6 times within a 12 second period. … You have 30 seconds to start lifting and lowering the lid. The motor has now been reset and is ready for you to start a cycle.
How do I reset my Whirlpool front load washer?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset. You can run a test load without any clothing to ensure that the reset worked.
How do I fix the Sud error on my Whirlpool Duet washer?
To solve this SUDS issue, finish your current load, if possible. Then run the washer on the largest load possible with no detergent and using hot water. This should rinse away the excess. However, if it still feels slimy inside, you may need to repeat as necessary.
How do I reset my Whirlpool Duet washer?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset. You can run a test load without any clothing to ensure that the reset worked.
What does e01 and f09 mean on a washing machine?
LONG DRAIN TIME
Don’t forget to share this post 
References and Further Readings :
