The 2 pin has its own built in starter and the 4 pin lamp is configured to use with external electronic control gear either of the standard or high frequency type.
A dead fluorescent can be caused by lack of electrical power (tripped breaker or blown fuse), a dead or dying ballast, a dead starter or a dead bulb(s). Check for power first… then the starter (if applicable) and then the bulbs. When all else fails, the ballast should be replaced.
Thereof, How do you remove a 2d 4 pin bulb?
Also to know is, What are light bulbs with two prongs called? A GU24 lamp fitting is a bi-pin connector for compact fluorescent lamps (CFL) or LED lamps that uses a bayonet mount–like twist-lock bi-pin connector instead of the Edison screw fitting used on many CFLs, LED lamps and incandescent light bulbs.
Subsequently, question is, How do you change a 2d 4 pin bulb?
Also, What are the signs of a bad ballast?
– Flickering. …
– Buzzing. …
– Delayed start. …
– Low output. …
– Inconsistent lighting levels. …
– Switch to an electronic ballast, keep lamp. …
– Switch to an electronic ballast, switch to a T8 fluorescent.
Are all 4 pin light bulbs the same?
4-pin plug-in CFL bulbs follow the same designation as other pin base with a “q” following the pin spacing number, which stands for quadruple, then either a 1, 2, or 3. … Plug-in CFL sockets are designed to only work with one style of pin base to ensure the correct light bulb is used to match the ballast in the fixture.
Why is my light bulb not working?
First check the bulb. … Tighten the bulb if it is loose, then try the switch again. If a problem remains, be sure the switch is off, remove the bulb and substitute a new one. If the light does not work with a new bulb, check whether the circuit breaker or fuse governing the fixture has tripped or blown.Apr 10, 1994
What causes a light socket to stop working?
By far the most common problem is a loose wire connection at the switch itself, which is subject to constant on-off usage. Less commonly, a light bulb socket may go bad. If so, you will need to replace the socket.
Do new fluorescent bulbs need to warm up?
All compact fluorescent lamps require a slight warm-up time for the electrical current to fully heat the cathodes and reach their full lumen output. When a bare spiral CFL is first switched on, it lights up with approximately 80% of its rated lumens, but it will heat up to its full brightness in about one minute.
How do you change a two pin fluorescent bulb?
What are the 4 types of light bulbs?
– There are four popular types of lightbulbs: incandescent, compact fluorescent (CFL), halogen, and light-emitting diode (LED). …
– Incandescent: These are the most commonly used type of bulb and are usually the least expensive.
What happens when a ballast goes bad?
If the ballast is bad, then the needle won’t move. If you’re using a digital multimeter, often the digital readout will possibly list a “1” when it doesn’t find a measurable resistance.
What is the difference between 2 pin and 4 pin lamps?
The 2 pin has its own built in starter and the 4 pin lamp is configured to use with external electronic control gear either of the standard or high frequency type.
Do LED light bulbs need to warm up?
Do LEDs need time to warm up? No they don’t. Unlike fluorescent lamps and energy-saving twisters that come on slowly or even flicker, LEDs shine with their full light output almost instantly after switching them on.
Why do some light bulbs have two prongs?
The two-pin bulbs are for use with magnetic ballasts, and the four-pin bulbs are for use with electronic ballasts. The sockets used in plug-in CFL fixtures are designed to work with only one style of pin base. This ensures that the correct wattage light bulb is used to match the type of ballast inside the fixture.
Do ballasts spoil?
When it’s too hot or too cold, the ballast can burn or fail to start your lamps at all. Heat combined with prolonged condensation inside an electronic ballast can cause corrosion. Some people may suggest removing the parts of the ballast casing and cleaning the electrical board.
Why do energy saving light bulbs need to warm up?
Because CFLs need added power to warm up, it’s more energy-efficient to leave one on than it is to repeatedly turn it on and off. Consequently, you may actually save energy by leaving the light on in a room that gets used frequently. … Temperature is more of a factor with CFL bulbs than with other ones, too.
Don’t forget to share this post 
References and Further Readings :
