There are pros and cons with each material, so it pays to make sure the type you choose works for your specific porch. Consider these things when choosing a porch floor: While natural fir is the traditional choice for a porch floor, good wood alternatives include cedar, mahogany and Brazilian Ipe.
The answer is yes. Creating a deck with tongue and groove lumber is as easy as creating a deck with traditional boards. First, cut all of your pieces into appropriate lengths. … This sinking action will allow the next deck board to slide into place and will perfectly conceal the previously installed screw head.
Thereof, How expensive is tongue and groove?
Cost. So, we know the tongue and groove ceiling looks awesome, but the big question is it affordable? According to the material you choose it can run anywhere from $2.00-$3.50 per square foot. It comes in many different wood species like knotty pine, clear pine, cedar, and redwood.
Also to know is, Does tongue and groove make composite decking? Composite Tongue and Groove Boards As one of the most popular types of decking, dozens of companies produce composite decking, but only a handful make planks with a tongue and groove profile.
Subsequently, question is, Can you use a router on composite decking? You can make simple cross cuts in composite decking the same way you would cut any soft pine—a power circular saw will work fine. … If installing the decking around an existing structure, a simple router can be used to make curved cuts.
Also, Can you use a router on Trex decking?
A: Yes, TrexTrim can be routed.
Can you screw down composite decking?
You can screw or nail composite decking boards just like wood ones. Three-inch decking screws are the best fastener choice; they sink a secure distance into the joists and won’t back out like nails. There’s little danger of splitting the boards when driving them, so you don’t need to pre-drill.
How do you fasten tongue and groove decking?
Using tacks, screws on nails, begin to fasten the flooring in place. This is the easy bit. Once you have installed the first plank, simply slide the next one into the groove of the previous plank. One effective method of fastening the floor into the frame is by using a pneumatic finish nailer.
How many boards do I need to cover a wall?
Use the square footage previously calculated to figure out how many boards are needed to cover the wall. Use the square footage and divide that number by the square foot of each board.
What is car decking lumber?
Car decking is 2x tongue and groove structural lumber and is usually douglas fir. I’ve never encountered cedar car decking. It was used on subfloors and was run diagonally across the floor joists.
Does roof sheathing need to be tongue and groove?
Tongue & Groove Boards The main reason to use tongue-and-groove boards these days is appearance – from beneath the roof. Say what you want about them but OSB and plywood do not offer a very attractive “finished” look.
What kind of paint do you use on Trex decking?
Choose an acrylic latex exterior primer (such as, Rustoleum Restore Deck Start Wood Primer or Valspar Exterior Multi-Purpose Water-Based Primer) and pour the bucket into your roller tray. Begin to apply the primer along the length of the planks.
Is shiplap cheaper than tongue and groove?
Shiplap is cheaper than tongue and groove, but it requires a bit more work on the carpenter to get the rows to lay flat against the building in a waterproof fashion. … However, a correctly installed exterior of shiplap siding has a finished appearance that appeals to many homeowners.
How do you install tongue and groove decking?
For installation, we suggest that you pre-drill a hole on a 45-degree angle where the tongue and the face meet. You will see a slight v-groove in this corner. Then, on that same 45-degree angle, drive a trim head screw through the pre-drilled hole, through the deck board into the floor joist.
How much does tongue and groove cost?
Cost. So, we know the tongue and groove ceiling looks awesome, but the big question is it affordable? According to the material you choose it can run anywhere from $2.00-$3.50 per square foot. It comes in many different wood species like knotty pine, clear pine, cedar, and redwood.
Does Trex make tongue and groove decking?
Outdoor luxury moves out front with Trex Trascend Porch flooring. Their advanced slanted tongue and groove board leaves no edges at all, creating a smooth finish. Their capped composite is built to last with a 25-year performance warranty that includes a 25-year stain and fade warranty.
How much does tongue and groove ceiling cost per square foot?
Installing a tongue and groove ceiling costs $2 to $3 per square foot using unfinished wood and an extra $1 to $3 per square foot if hiring your local handyman.
How many rolls of wallpaper do you need for one wall?
20 rolls
Don’t forget to share this post 💖
References and Further Readings :