Ambient Temperature (°F) Low Side High Side
———————— ——— ———–
80° 45-50 psi 175-220 psi
75° 40-45 psi 150-175 psi
THE HIGH SIDE NEEDLE SHOULD POINT TO A TEMPERATURE BETWEEN 105 AND 115 (in the green ring of numbers) AND THE PRESSURE IS READ ON THE BLACK RING OF NUMBERS FOR PRESSURE. … IF the return temperature is 75 the evaporating temperature of the R-22 should be between (75-40=35) and (75-35=40).
Thereof, What is suction and discharge pressure of r410a?
Suction pressure of an Air-Conditioner with R410A Refrigerants typically ranges between 115 Psig to 125 Psig when operated at an ambient temperature of 35 degC. The discharge pressure at this operating conditions hovers around 400 Psig. R-410A operates at pressures 50 to 70% higher than those of R-22.
Also to know is, How do you read AC gauges for r22?
Subsequently, question is, What are normal operating pressures for 410a? A normally operating R-410A system with the same condensing temperature of 120 degrees and a 45 degree evaporator saturation temperature will have a high side pressure of 418 psig and a low side pressure of 130 psig.
Also, What is suction and discharge pressure?
Discharge pressure (also called high side pressure or head pressure) is the pressure generated on the output side of a gas compressor in a refrigeration or air conditioning system. … An extremely high discharge pressure coupled with an extremely low suction pressure is an indicator of a refrigerant restriction.
What should my Pressures be for r22?
Ambient Temperature (°F) Low Side High Side
———————— ——— ———–
75° 40-45 psi 150-175 psi
70° 35-40 psi 140-165 psi
How do you read a r22 pressure temperature chart?
What should the high and low side pressures be?
Actual readings will vary according to ambient temperature. The low-side should be near 30 PSI at 90 degrees Fahrenheit or less. Pressure that is too much lower or higher shows there is a problem. On a properly working system, high-side pressure will be about twice the ambient temperature, plus 50 PSI.
What will happen to the system if suction pressure is higher than the discharge pressure?
Because discharge gases have leaked through the rings and into the crankcase, suction pressure will also be higher than normal. The resulting symptom will be a lower head pressure with a higher suction pressure. The symptoms for worn rings on a compressor are very similar to leaky valves.
What is normal subcooling for r22?
Subcooling on systems that use a thermostatic expansion valve (TXV) should be approximately 10F to 18F. Higher subcooling indicates excess refrigerant backing up in the condenser. On TXV systems with high superheat, be sure to check the subcooling as refrigerant is added.
What is the normal suction pressure?
Your desired suction pressure is 33-48 degrees or 58-80 psi depending on the indoor temperature. (Note: The hot or warm air from a hot house traveling across the evaporator coil will warm the refrigerant faster than normal causing a higher suction pressure.
What causes high suction pressure and low discharge pressure?
The main reasons your compressor will have simultaneously low head pressure and high suction pressure is due to: Bad or leaky compressor valves. Worn compressor piston rings. Leaky oil separator return line.
What are normal pressures for r22?
If the system had R-22, the vapor pressure would be between 58 to 85 PSIG but these pressures will be dependent on the wet bulb temperature inside the building and the ambient temperature outside the building.
What is the low and high pressure for r22?
For a low pressure gauge, a reading of 25 pounds per square inch (psi)to 40 psi is optimum. On the other hand, a high pressure gauge should read between 225 psi and 250 psi.
What is a pressure temperature chart?
The pressure-temperature (PT) chart is a valuable tool that service technicians use to check proper system operation. … Traditional PT charts list the saturated refrigerant pressure, in psig, with a column for temperature down the left side.
What are the normal operating pressures for r22?
If the system had R-22, the vapor pressure would be between 58 to 85 PSIG but these pressures will be dependent on the wet bulb temperature inside the building and the ambient temperature outside the building.
What should AC gauges read r22?
IF the return temperature is 75 the evaporating temperature of the R-22 should be between (75-40=35) and (75-35=40). THE LOW SIDE NEEDLE SHOULD POINT BETWEEN 35 AND 40 DEGREES (in the green ring of numbers) FOR R-22 AND THE PRESSURE IS READ WHERE THE NEEDLE POINTS ON THE BLACK RING OF NUMBERS FOR PRESSURE.
Don’t forget to share this post 
References and Further Readings :
