144959. AYP / Craftsman / Sears Deck Belt fits 42″, 46″ & 50″ Decks built since 1995. Size: 1/2″ x 95-1/2″. Replaces part numbers 532144959 and 144959.
Thereof, How do you put a drive belt on a Troy Bilt riding lawn mower?
Also to know is, How do you put a drive belt on a Troy Bilt Bronco riding mower?
Subsequently, question is, What size is my mower deck? Lie down on the ground next to the elevated mower, and pass the tape measure beneath the blades, hooking it on the opposite side of the deck. Note the distance on the tape measure. This is your deck size.
Also, How do you measure a mower deck belt?
– Lay the belt flat on a hard surface.
– Measure the belt by wrapping the cloth tape measure around the belt. For broken belts, simply measure the total length of the belt.
– Hold the cloth tape measure against the length or width of the belt depending upon which measurement you need.
What size belt does a Troy Bilt Pony take?
Troy-Bilt Pony tillers have two belts, a forward drive belt, which measures 4L by 23.80 and a reverse drive belt, which measures 3L by 27.44, located in the “tine and drive” assembly.
What size mower belt do I need?
There’s no standard size for a 42-inch-cut riding mower. Each model uses a different size belt. To give examples, some models use a drive belt that is ½ inch wide by 92 inches in length, while others use a belt ½ inch wide by 85 inches in length.
How wide is a 48 inch mower deck?
Registered. My 48″ deck with the guard up is just a tick over 51 inches. It was a real tight fit on a friends trailer that was 54 inches wide. You need a few inches in case of high spots or low spots on either side of the rocks to manuever around.
What size of mower do I need?
Look for a mower with at least 14-16 hp and a wide mowing deck – at least 38 inches – to get your lawn work done quickly. Yards larger than three acres are best handled by a larger zero-turn rider or a garden tractor. Look for models that have at least 18hp engines and mowing decks in the 44-54 inch range.
Does a 1/2 acre need a riding mower?
For lawns over 1/2 acre, we recommend upgrading to a riding mower. If cutting time is important and you have a lot to cut, you need a fast riding mower with a 40-60 inch+ cutting deck.
What size belt do I need for a 42 inch deck?
There’s no standard size for a 42-inch-cut riding mower. Each model uses a different size belt. To give examples, some models use a drive belt that is ½ inch wide by 92 inches in length, while others use a belt ½ inch wide by 85 inches in length.
Does a 1/4 acre need a riding mower?
An acre is 43,560 square feet, so one-fourth acre is 10,890 square feet. Anything above that threshold, and you’ll likely want to get a riding mower.
What size blades do I need for a 42 inch deck?
2 blades
What size mower deck should I get?
Lawn Size. Typically, the larger the lawn, the wider the cutting deck size needed. … If your lawn is 1/2 to 2 acres, then a riding mower with a deck that is 42 to 48 inches wide would be appropriate. If the lawn is 3 acres or larger, the deck should be at least 50 inches wide.
How do you measure a mower deck width?
If there is no obstruction, feed your tape measure through the pulleys, across the center of the deck, and hook it on the opposite side. For a round deck, locate the widest area of the circle, or the diameter, and extend your tape measure across that area. Note the distance on your tape measure. This is your deck size.
How wide is a 42 inch mower deck?
1334 mm
How Do You Measure V belt size?
Use a cloth measuring tape (not a steel one) and wrap it around the outside of the belt. You also use a thin string to take this measurement and place it on a steel tape to get the correct length. Next, for “A” Belts (1/2” width) subtract two-inches from the outside measurement to select the correct V-belt.
Don’t forget to share this post 
References and Further Readings :
