The 3/4-inch-thick subfloor takes a 2-inch screw. A thicker subfloor takes a 3-inch screw.
Screw Selection Chart
——————— —– ——
Plywood Thickness Screw Length
3/4″ #8 1-1/2″
5/8″ #8 1-1/4″
1/2″ #6 1-1/4″
Thereof, Can screws hold in plywood?
* Nails, brads or screws won’t hold in the edges of thin plywood. However, you can sink screws into the edges of three-quarter-inch plywood if you drill pilot holes and center the screws on the edge. * When nailing into face plies, space nails at four-inch intervals for maximum panel strength.May 30, 1992
Also to know is, What thickness subfloor is recommended? The recommended thickness of the plywood subfloor is governed by the spacing of the joists. Some experts suggest that 15/32-inch plywood should be standard if the underlying floor joists are spaced 16 inches apart or less, but slightly thicker 3/4-inch plywood should be used for joists spaced further apart.
Subsequently, question is, What screws to use on plywood? For construction outdoors, such as an exterior stairway, zinc coated nails or decking screws should be used to attach plywood. These are designed to prevent rusting, which destroys the fastener.
Also, How thick should a floor be?
In a typical home, the entire structure between levels can be about 12 to 14 inches thick, depending on the type of joists used and the finish materials for the floor and ceiling.
What screws do you use for plywood?
For construction outdoors, such as an exterior stairway, zinc coated nails or decking screws should be used to attach plywood. These are designed to prevent rusting, which destroys the fastener.
Can you put screws into plywood?
* Nails, brads or screws won’t hold in the edges of thin plywood. However, you can sink screws into the edges of three-quarter-inch plywood if you drill pilot holes and center the screws on the edge. * When nailing into face plies, space nails at four-inch intervals for maximum panel strength.May 30, 1992
Is it better to nail or screw plywood?
Answer: It is better to use screws on plywood instead of nails. Screws are more suitable for the soft plywood blocks since they can be removed more easily and do not cause splintering. You don’t have to worry about splitting the wood by using screws.
What is the best material for subfloor?
Plywood
Should subfloor be screwed or nailed?
Although ring shank nails have a good hold, screws have more overall holding power by comparison. With a larger thread gripping a bigger surface area around them, screws hold your subfloor very tightly – allowing no wiggle room for shifting or loosening.
How many screws do I need for a 4×8 subfloor?
82 screws
What kind of nails do you use for plywood?
When nailing plywood to 2”x 4” structural elements, 8d (eight penny) common nails are almost always used. It is not necessary to use the longer 16d nails that are commonly used in attaching 2”x 4” studs and other 2” thick structural elements together, as the plywood is thinner than that.
Should I use nails or screws for plywood?
Answer: It is better to use screws on plywood instead of nails. Screws are more suitable for the soft plywood blocks since they can be removed more easily and do not cause splintering. You don’t have to worry about splitting the wood by using screws.
How do you hide screws in plywood?
How many screws are in a 4×8 sheet of subfloor?
82 screws
What screws to use on plywood floors?
The proper steel screw sizes for securing 3/4-inch plywood to the floor joists are #8, #10 and #12 screws. The number refers to the thickness of the screw. Each is available in lengths from 1 1/4 to 3 inches. Typically, the 3-inch variety is used to secure plywood subfloors.
Can I use a brad nailer on plywood?
To sum up, using a Brad or Framing nailer on plywood is pretty straightforward, once you know what to look for. … If you are not sure what thickness plywood you will be using, then a 15 or 16 gauge nailer can be used reliably on most plywood boards.
Don’t forget to share this post 
References and Further Readings :