The right socket for water heater element is Drive x 1-1/2 inches socket. Designed to properly the all common size electric heater elements, this socket’s opening will snugly fit the hex end. This is to allow you to use the most appropriate torque without slipping.
When selecting element, buy same wattage or less wattage… keep volts the same. It is ok to install higher watt up to 5500 on 4500 watt heater if breaker is 30 amp and wire is 10 gauge. It is ok to install lower watt: replace 4500 with 3500 as long as voltage is same.
Thereof, Can I replace a 3800 Watt water heater with a 4500 Watt?
Also question is, can I replace a 3800 Watt water heater with a 4500 Watt? You can buy 3800 watt elements to replace the 4500 watt units. This is commonly done when the electric is NOT 10 gauge wire with 30 amp breaker. If it is 12 gauge and 20 amp you are limited to 3800 watt elements.
Also to know is, What size breaker do I need for a 4500 watt water heater? A 4500-watt element requires 10/2 wire and a 30 amp (220volt) breaker. The 3800 can be wired with 12/2 wire and a 20 amp breaker.
Subsequently, question is, Can you replace a 4500 watt heating element with a 5500 Watt? The short answer to the question is yes, as long as you have the correct breaker and wire system set up. If the breaker is 30 amp, then yes, a 5500-watt water heater should be fine as a replacement for a 4500-watt water heater.
Also, What size breaker do I need for a 5500 watt water heater?
Full power that is 23 amps. Pumps should be around an amp.
How do you get a stuck element out of a hot water heater?
Mix a solution of half vinegar and half water in a small cup. Dip a toothbrush into the solution and brush it between the seam of the heating element and the side of the heating tank. Apply the solution liberally, but do not allow it to drip heavily. Allow the solution to sit for 20 minutes.
What size breaker do I need for a water heater?
Electric water heaters require a 240-volt dedicated circuit, which serves only the water heater and no other appliances or devices. The circuit wiring typically includes a 30-amp double-pole breaker and 10-2 non-metallic (NM) or MC cable.
What happens when a heating element goes out in a water heater?
If you have an electric water heater, the heating elements inside the tank can break and lead to a loss of hot water. Sometimes, your water will slowly start to cool down and this could be because the element has burned out. If the second element fails, you’ll be left with only cold water.
How do I test a hot water heater element?
How many ohms should a water heater element have?
Check the resistance of the upper heating element using a multimeter. Measure the resistance between the two screw terminals on the upper heating element. A good element will have a resistance between 5 and 25 Ohms.
How many amps is a 4500 watt water heater?
18.75 amps
How do I know if my hot water heater element is bad?
How many amps does a 4800 watt heater use?
30 amp
Do I have to drain water heater to change element?
It is possible to change your water heater’s heating element without draining your tank.
Can I replace a 4500 Watt water heater with a 3800 Watt?
You can buy 3800 watt elements to replace the 4500 watt units. This is commonly done when the electric is NOT 10 gauge wire with 30 amp breaker. If it is 12 gauge and 20 amp you are limited to 3800 watt elements.
How do you check to see if a water heater element is bad?
Touch a probe on the multitester to each screw on the element. If you get no reading, or a maximum reading, the element is bad. Elements do have some resistance, so a reading of 10-16 ohms is normal, with higher ohm readings for 3,500 watt elements and lower readings for 5,500 watt elements.
How many amps is 4800 watts at 240 volts?
20 amps
Don’t forget to share this post 💖
References and Further Readings :
