150 Foot Run – A 120-volt circuit on a 20 amp breaker will require 6/2 AWG wire for 150 feet.
> 150ft. from main? The minimum wire size you can run to a 100A panel is #4 copper or #2 aluminum.
Thereof, What size wire do I need for 100 amp service?
The cable must have a wire gauge sufficient to the amperage of the subpanel—a 100-amp subpanel requires #4 copper wires, for example.
Also to know is, What size wire do I need for a 100 amp service? You need a 3-3-3-5 copper SER cable to carry 100 amps (that’s three #3 gauge for the two hot wires and the neutral and a #5 gauge for the ground).
Subsequently, question is, What size wire do I need for a 100 amp breaker? The cable must have a wire gauge sufficient to the amperage of the subpanel—a 100-amp subpanel requires #4 copper wires, for example.
Also, Will 2 wire fit in a 100 amp breaker?
#2 romex would only be good for 95 amps. If protected with a 100 amp breaker be prepared to show load calcs that load is 95 amps or less.
What size wire is needed for 100 amps?
You need a 3-3-3-5 copper SER cable to carry 100 amps (that’s three #3 gauge for the two hot wires and the neutral and a #5 gauge for the ground).
What size wire do I need for underground?
14 AWG 50 feet
—— ——-
12 AWG 60 feet
10 AWG 64 feet
8 AWG 76 feet
6 AWG 94 feet
What size wire do I need for two hundred amp service?
You need a minimum of #6 ground or #4 aluminum for 200 amps.
How far can you run 10 gauge wire?
14 AWG 100 feet
—— ——–
12 AWG 120 feet
10 AWG 128 feet
8 AWG 152 feet
6 AWG 188 feet
What is #2 wire rated for?
Copper
– ——
4 70
3 85
2 95
1 —
What size conduit do I need for a 100 amp service?
How far can you run 12 gauge wire on a 20 amp circuit?
You can run a 10 gauge wire up to 85 feet on a 20 amp circuit. If you opt to use this type of wire on a 15 amp circuit, it can run up to 115 feet. After these distances, the circuit will go over the recommended 3% voltage drop. You can run a 12 gauge wire up to 70 feet on a 15 amp circuit.
What size breaker do I need for a sub panel?
Based on your question, since you will be having a subpanel, you want the breaker feeding the subpanel to be sized for the subpanel or slightly smaller. So if you purchase and install a 200A subpanel, then the breaker should be 200A. If you use a 125A subpanel, then use a 125A breaker.
Will #2 wire fit in a 100 amp breaker?
Sub Panels When it comes to the lines connecting master and secondary panels, where the line will carry as much as a full 100 amps, use a 2-gauge non-metallic sheathed electrical cable. … Each wire should be 2-gauge in size.
How far can 10 gauge wire carry 30 amps?
150 feet
What size wire do I need for a 200 amp underground service?
Herein, what size wire do I need for a 200 amp underground service? You need a minimum of #6 ground or #4 aluminum for 200 amps. I would recommend just getting 4/0-4/0-2/0-4 quadplex as it is all rated for direct burial. A conductor is a wire that is used to carry electrical power.
What size wire do I need for a 60 amp subpanel?
That would be 4-gauge wire. In practice, however, it’s common to wire 60-amp breakers with 6-gauge, 3-conductor wire because an appliance that needs a 60-amp breaker seldom draws the full 60 amps. If you’re installing a 60-amp subpanel, however, it’s best to connect it to the main panel with 4-gauge wire.
Don’t forget to share this post 
References and Further Readings :
