Pro tip: In most cases, a tripped circuit breaker is caused by a temporary overload on the circuit or a short circuit in some device plugged into the circuit. But in rare cases, a loose wire in an electrical box could be causing the problem.
If it was a short the circuit breaker would have tripped. If that receptacle is the only one on that circuit then it shouldn’t affect any other circuits. … If that is the case, then the washer receptacle is being used as a pass thru receptacle and must be replaced immediately.
Thereof, Why would an outlet have power but not work?
There can be a number of reasons a receptacle stops working. The problem could be as simple as a loose connection; the wires could also be damaged, which might require a brand new circuit. A device might still be working, but could have serious—and potentially dangerous—underlying issues.
Also to know is, Can a bad outlet make other outlets not work? If there is no GFI reset button, then your issue may be that one outlet is damaged or has a loose wire. This could be causing the other outlets to also have no power. In simple terms, the outlets that are not working may be daisy chained. Think of it like the old Christmas lights.
Subsequently, question is, How can you tell if an outlet is bad?
Also, What causes low voltage at outlet?
Low voltage from household outlets typically stems from a worn-out or damaged fixture. Over years of use, outlets sustain wear and tear just like other frequently used items. Over time, plugging and unplugging cords causes the connections within the plug to loosen, which wears away the outlet.
Can a breaker cause low voltage?
There is a voltage drop across the breaker, if it is in good condition it should be negligible for most cases though. If the breaker is suspected to be making a significant contribution to voltage drop measure from bus to output terminal and see just how much drop there is.
Can a bad electrical outlet affect others?
If it was a short the circuit breaker would have tripped. If that receptacle is the only one on that circuit then it shouldn’t affect any other circuits. … If that is the case, then the washer receptacle is being used as a pass thru receptacle and must be replaced immediately.
How do you troubleshoot a bad electrical outlet?
– Determine if what’s plugged into the outlet isn’t working. Unplug whatever is plugged into the outlet and plug it into another outlet. …
– Check and see if other outlets are dead. This is easy enough to do. …
– Check the circuit breakers. …
– Check Ground Fault Circuit Interrupter (GFCIs) outlets. …
– Look for a bad connection.
How many devices can you have on an outlet?
two appliances
Does voltage matter on a circuit breaker?
Circuit breakers are typically marked only with a few standard voltages, while other voltage systems exist. Resolution: Yes. According to 2011 NEC article 240.83(E), a circuit breaker may be used at voltages equal to or less than its’ voltage rating.
How do you fix a dead outlet?
– Step 1: Make sure the problem isn’t with the appliance. …
– Step 2: Check for a switch to the outlet. …
– Step 3: Look for a tripped GFCI breaker. …
– Step 4: Check the breaker panel. …
– Step 5: Tighten the outlet electrical connections. …
– Step 7: Call an electrician.
What causes a plug to stop working?
When a wall outlet doesn’t work, there are two possible reasons: a bad connection or a tripped breaker. The bad connection is usually in the outlet itself, and finding the tripped breaker may boil down to simply locating the nearest ground fault interrupting outlet. GFIs can cut power to other outlets when they trip.
How much does it cost to fix a dead outlet?
Outlet repair costs vary depending on the type of outlet and its location. Most homeowners can expect to pay between $65 and $200 for the project. How long does it take to repair an outlet? It usually takes about an hour to test a receptacle, fix loose connections or install a new outlet.
Can a circuit breaker cause low voltage?
There is a voltage drop across the breaker, if it is in good condition it should be negligible for most cases though. If the breaker is suspected to be making a significant contribution to voltage drop measure from bus to output terminal and see just how much drop there is.
What happens when you plug too many things into one outlet?
A power point overload occurs when you exceed the maximum amperage of the electrical circuit you are using. This can be caused by plugging too many appliances into the one power point or running appliances that draw high amps at the same time. The result of an overload can be a short circuit and quite possibly a fire.
What happens if voltage is too low?
If the voltage is too low, the amperage increases, which may result in the components melting down or causing the appliance to malfunction. If the voltage is too high, this will cause appliances to run ‘too fast and too high’ which will shorten their service life.
How do you fix a low voltage outlet?
Once you discover a low voltage electrical outlet, unscrew the plate and locate the ground, neutral and hot voltage wires. Tighten the screws that hold these wires in place. This might fix your issue. If any of the wires look corroded, strip them until you see shiny copper and clean the connections.
Don’t forget to share this post 
References and Further Readings :