A: Mix 3.2 ounces of Poulan 2-cycle air cooled engine oil to one gallon of fresh unleaded gasoline to obtain the recommended 40:1 fuel to oil ratio. Over a period of time oil will separate from gasoline.
Thereof, How do I make 2 stroke fuel for my chainsaw?
Also to know is, How much oil do I need for a 50 to 1 ratio? For a 50:1 ratio of gas to oil, use 2.6 fluid ounces of oil per gallon of gas. For a 40:1 mixture, use 3.2 fluid ounces of oil per gallon of gas. For a 32:1 mixture, use 4 fluid ounces of oil per gallon of gas.
Subsequently, question is, Where do the fuel lines go on a chainsaw? The (clear) fuel intake line runs from the top of the carburetor (straight nipple) and goes to the short post on the back of the primer bulb. The return line (blue) comes from the long post on the back of the primer bulb and goes into the bottom of the fuel tank.
Also, What kind of fuel does a Poulan chainsaw use?
A: Our units run on 87 octane regular unleaded gasoline. You can use gasoline which is blended with a maximum 10% alcohol. Never use E85 or diesel fuels. Remember to use fresh gasoline and to mix it with the recommended 2-cycle oil.
How much oil do I add to 5 Litres of petrol?
Fuel Amount (Litres) 50 : 1 Ratio (ml) 100 : 1 Ratio (ml)
——————– —————– ——————
5 L 100 ml 50 ml
10 L 200 ml 100 ml
15 L 300 ml 150 ml
20 L 400 ml 200 ml
What does 50/1 mean when mixing gas and oil?
50:1 means for every 50 ounces of gasoline you need to mix in 1 ounce of oil. If you are using a 1 gallon gas can you would take 128 ounces (1 gal) divided by 50 = 2.56.
How do you replace the fuel lines on a Poulan trimmer?
Can I use 2 stroke oil for chainsaw?
AMSOIL SABER Professional Synthetic 2-Stroke Oil is tested and proven at any mix ratio up to 100:1. That means you can mix one can of fuel and use it in all your two-stroke equipment. Done.
How do you calculate a 50 to 1 ratio?
You want to mix 2.6 ounces of oil to one gallon of gasoline for a 50:1 mixture. If you’re mixing up two gallons of gasoline you will have to mix 5.2 ounces of oil to two gallons of gasoline for a 50:1 mixture. I would recommend using fresh gasoline that has an octane rating of 89.
How do you route fuel lines on a chainsaw?
How do you install fuel lines on a Poulan chainsaw?
What happens if you mix too much oil in a 2 stroke?
Excess oil can produce a smoky exhaust, oil leaking out of the muffler, and sometimes loss of power. While not ideal, these issues can be fixed by simply replacing the fuel in the tank with properly mixed fuel. But running a two-cycle engine with too little oil can actually destroy the unit.
Can I use 2 stroke oil for chain oil?
For mix oil, you must use the petroleum-based 2-stroke mix oil recommended by the chain saw manufacturer.
What is the ratio for 2 stroke fuel mix?
40:1
How do you make 2 stroke fuel?
– For a 50:1 ratio of gas to oil, use 2.6 fluid ounces of oil per gallon of gas.
– For a 40:1 mixture, use 3.2 fluid ounces of oil per gallon of gas.
– For a 32:1 mixture, use 4 fluid ounces of oil per gallon of gas.
What kind of fuel does a chainsaw use?
Mid-grade unleaded gasoline with a minimum octane rating of 89 is recommended for your mixture. Fuel with a lower octane rating may increase engine temperatures, increasing the risk of piston seizure and damage to the engine.
Don’t forget to share this post 
References and Further Readings :
