Dislocated or Damaged Wiring Damaged or disrupted wiring can cause tail lights not to work, but brake lights are. The two lightings use different wiring as each bulb has got its power supply. A recent accident at the tail end of your car can increase the likelihood of this problem.
It could be bad or one of the fuses that power up this relay could be blown. … They are, fuse 32 (7.5 amp) and fuse 9 (15 amp fuse). They are both located in the in the under dash fuse relay box.
Thereof, Why is my tail light melting?
the tail light is melted and need to know if it could be an electrical issue. Check to be sure the bulb is the correct number. If it’s too large (physically) it may be too close to the lens, or if it is too high a wattage for the light, it would just get too hot, and could melt the plastic lens.
Also to know is, What does it mean when your tail lights don’t work? Blown Fuse: As a first resort, a mechanic should expect the corresponding fuse for your rear lights. … Burned Out Bulbs: In the case where only one of your rear lights appears to be out, the cause is most likely a burned out bulb. When the filament breaks inside a bulb, it cannot illuminate the gas inside the bulb.
Subsequently, question is, Why are my LED tail lights not working? Or, do your tail lights not work correctly? The reason for this is your cars computer thinks your bulb in burnt out. LEDs don’t use much power and don’t put a the current draw (LOW resistance) needed across the terminals of your tail, signal, or break light.
Also, How do you fix a burnt tail light?
– Step 1: Locate the tail light access panel. …
– Step 2: Unbolt the tail light housing. …
– Step 3: Unlock the tail light socket. …
– Step 4: Inspect the wiring. …
– Step 5: Remove and inspect the bulb. …
– Step 6: Replace the bulb with a brand new one. …
– Step 7: Test out the new bulb.
Why won’t my tail lights and dash lights work?
It could be that the dash and taillights share a common fuse. … So, if you do find a blown fuse, you’ll need to track down the reason it blew in the first place. Other potential causes for your problem include a short somewhere in the circuit or a faulty light switch.
Why are my rear running lights not working?
Common causes for this condition is a loose fitting bulb inside the socket. … If the bulb flickers tighten the socket or replace the bulb/socket to regain proper operation. If the complete system flickers (all bulbs flicker) wiggle the tail light fuse, relay and associated wiring at the headlight/tail light switch.
Why are my rear lights not working?
Blown Fuse: As a first resort, a mechanic should expect the corresponding fuse for your rear lights. … Burned Out Bulbs: In the case where only one of your rear lights appears to be out, the cause is most likely a burned out bulb. When the filament breaks inside a bulb, it cannot illuminate the gas inside the bulb.
Do tail lights and brake lights use the same bulb?
Tail light works, brake light doesn’t. Two filaments-One bulb. …
Can you fix LED tail lights?
LED tail lights have a high failure rate. Fortunately, they’re easy to repair or replace as a do-it-yourself job. Although LED tail lights are designed to last, moisture may enter worn housings and could corrode circuit boards, causing the resistors to fail. This will lead to LED burn out or dimming of the bulb.
Should you replace both brake lights at the same time?
The answer is, no, it’s not required to replace both bulbs. There are some advantages, however, to getting a professional Ace Auto Parts mechanic to change both lights at the same time. The most important reason for changing out all headlights at the same time is that you don’t want both headlamps to go dark.
How much does it cost to fix a burnt out tail light?
Replacing one brake or tail light bulb in an average car will cost $10-$55 labor plus the cost of the bulb ($1-$7). In some cars it’s very easy to do; in others the taillight assembly might need to be removed in order to replace a bulb.
How do I fix my tail lights?
Can AutoZone change a tail light?
An AutoZone store employee may be able to help you replace your brake lights, tail lights, headlights, and other exterior car lights, but the company does not officially offer this as a service, an AutoZone corporate customer service representative said.
Why does my tail light fuse keep blowing out?
Somewhere your wiring or one of the bulbs on the brake light circuit probably has a dead short to the ground, which is the frame of the car. Don’t forget any add-on trailer harness. A likely cause is where something heavy has laid upon the wire, pinched it and worn through over time with vibration.
What would cause my tail lights to not work?
Dislocated or Damaged Wiring Damaged or disrupted wiring can cause tail lights not to work, but brake lights are. The two lightings use different wiring as each bulb has got its power supply. A recent accident at the tail end of your car can increase the likelihood of this problem.
Why are my parking lights not working?
check the front bulbs also since they are on the same parking light fuse circuit. One of the bulbs may be bad. … The first thing you should do is replace the rear bulbs for the parking lights since they may be intermittently grounding out inside the bulbs. If still continues then replace front bulbs.
Don’t forget to share this post 
References and Further Readings :