Why does my timer show “off pwr” in the LCD display? This can be caused by: • Disconnected power supply. A blown fuse (in some models). The electrical outlet is not working.
The NO AC display is a diagnostic message telling you that the controller has stopped receiving AC power. The controller is running on the power supplied by the backup battery. Check the power source by plugging a lamp or radio into the wall outlet to verify there is power at the outlet.
Thereof, How do I turn off orbit sprinkler timer?
Reset to Factory Default – Orbit Irrigation B-hyve Help. To reset your timer back to factory settings: Turn the timer to the OFF position by rotating the dial. Open the front swing panel and press and hold the reset button for 10-12 seconds.
Also to know is, How do I reset my Hunter SRC Plus controller? – Press and hold down the , and buttons.
– Press and release the RESET button in the lower wiring compartment.
– Release the , and buttons. The display should now show 12:00am. All the memory has been cleared and the controller may now be reprogrammed.
Subsequently, question is, How do I turn off my orbit sprinkler system? Open the top of the valve and remove the diaphragm. Turn on the water supply and flush the valve out for 15 seconds.
Also, How do I reset my sprinkler controller?
– Turn the control dial to the “off” position.
– Press the “next” button to access the clear-memory feature. …
– Press and hold the “off” button until the display stops blinking.
– Turn the control dial to the “run” position.
– Press and hold down the “minus” arrow and “prog” buttons simultaneously.
How do I turn off my orbit sprinkler valve?
Open the top of the valve and remove the diaphragm. Turn on the water supply and flush the valve out for 15 seconds.
Why does my sprinkler system not work?
Go to one of the irrigation valves and turn the solenoid 1/4 to 1/2 a turn counter-clockwise. If the valve opens and sprinklers turn on, your valve is working and you’ll need to check the controller and field wiring. If the valve did not turn on any of the sprinklers, the water to the valves is still off.
How do you fix an orbit water timer?
How do you troubleshoot an orbit sprinkler system?
– Check the programming settings if one or more stations are not turning on. …
– Check the valves in the ground sprinkler controls if some of the stations are not working. …
– Make sure the timer dial is set to “Auto.” If it is set to something other than “Auto,” the sprinklers will not turn on at the programmed times.
How do you troubleshoot a hunter sprinkler controller?
– STEP 1: Check Device (Remote Receiver) …
– STEP 2: Check SmartPort Wiring. …
– STEP 3: Replace the.
– STEP 1: Verify Station Fault. …
– STEP 2: Check Valve Wiring. …
– STEP 1: Check Master Valve Solenoid/Wiring. …
– STEP 2: Check Pump Relay.
How do I reset my Hunter SRC?
– Press and hold down the , and buttons.
– Press and release the RESET button in the lower wiring compartment.
– Release the , and buttons. The display should now show 12:00a. m.
– All the memory has been cleared and the controller may now be reprogrammed.
What does no AC mean on my sprinkler system?
prime power source
How do I reset my Hunter controller?
– Unplug the controller’s transformer.
– Press and hold down the, and buttons.
– Plug the controller’s transformer back in.
– Release the , and buttons. The display should now show 12:00am. All the memory has been cleared and the controller may now be reprogrammed.
How do you unstick a sprinkler valve?
Why is my orbit Sprinkler not working?
Turn the flow-control stem located at the connection from the Orbit to the main water line in a counterclockwise direction if one or more of the sprinklers is not responding to programming. If the problem persists, check the wired connections of the device to make sure they are correct.
How do you program an orbit watering system?
How do I reset my orbit sprinkler system?
– Push the “Reset” button (located in the bottom-right corner) to clear all previously programmed data if you’re programming the Orbit sprinkler timer for the first time.
– Twist the dial to “Time/Date” to set the date. …
– Twist the dial to “Start Times (A)” to adjust the watering schedule for program A.
Don’t forget to share this post 
References and Further Readings :