Impeller is clogged – If the pump’s impeller is clogged with debris, water will not be able to flow out the side slots and generate a vacuum. Without a vacuum, the pump will not be able to suck water into the pump and it will not prime. Remove the impeller and clean out the debris.
– Clogged pump basket or skimmer baskets.
– Clogged pump impeller.
– Eyeball fittings not in place at pool returns.
– Filter valve allowing water to bypass filter.
– Air pulling into system at pump intake or pump lid, or valves.
Thereof, When should you vacuum pool to waste?
You’ll also need to vacuum to waste when there is a large amount of debris or leaves in the pool, usually at opening. Vacuuming to WASTE can only be accomplished if a multiport valve controls your pool filter system. This position bypasses the filter and sends all the unwanted debris through the waste line.
Also to know is, Why does my pool skimmer have no suction? Conversely, when the pressure gauge reads lower than normal, this indicates a problem with the suction side of the system, either a clogged pump impeller, clogged pump basket, closed valves (skimmer/main drain) or a clog in the pipe, an incoming air leak, or on skimmers that used flex pipe underground, a collapsed …
Subsequently, question is, Why does my pool have no suction? Suction-Side Problems Possible reasons for this problem include the following: The water level in the pool is too low. Make sure the water is high enough to cover all the skimmers—if there is more than one—and all the return jets. The suction hose for the vacuum has holes, or it isn’t fully connected.
Also, How do I increase the suction on my pool pump?
Do you vacuum a pool on backwash or waste?
This option allows you to vacuum the algae up and send it out through the backwash line, avoiding getting algae into your filter sand. However, you will need to vacuum quickly, as water will be exiting your pool quickly. You should not let your water line fall below your skimmer at any time.
Why does my pool pump have no suction?
Impeller is clogged – If the pump’s impeller is clogged with debris, water will not be able to flow out the side slots and generate a vacuum. Without a vacuum, the pump will not be able to suck water into the pump and it will not prime. Remove the impeller and clean out the debris.
Do you vacuum pool on waste or filter?
You’ll also need to vacuum to waste when there is a large amount of debris or leaves in the pool, usually at opening. Vacuuming to WASTE can only be accomplished if a multiport valve controls your pool filter system. This position bypasses the filter and sends all the unwanted debris through the waste line.
What causes low pool filter pressure?
It could be a clogged pump basket, clogged impeller, clogged pipe or clogged skimmer. It could also be a closed or broken valve before the pump. Or, the pump may have an air leak, and is drawing in more air than water, which will also reduce the filter pressure (and filtration).
What do I set my pool pump to when vacuuming?
For routine vacuuming, the filter valve is left in the normal “Filter” position. This directs dirty vacuum water through the pool filter to remove the contaminants, then conveys filtered water through return lines back to the pool. The “Filter” setting is used for light to moderate levels of pool sediment.
What setting do you put your pool filter on when vacuuming?
For routine vacuuming, the filter valve is left in the normal “Filter” position. This directs dirty vacuum water through the pool filter to remove the contaminants, then conveys filtered water through return lines back to the pool. The “Filter” setting is used for light to moderate levels of pool sediment.
How do I fix my pool pump suction?
How do I fix the suction on my pool vacuum?
How do you vacuum a pool with a sand filter?
What setting do you vacuum a pool on?
For routine vacuuming, the filter valve is left in the normal “Filter” position. This directs dirty vacuum water through the pool filter to remove the contaminants, then conveys filtered water through return lines back to the pool. The “Filter” setting is used for light to moderate levels of pool sediment.
Where does debris go when you vacuum a pool?
As the skimmer pulls water through the vacuum tool, the vacuum head is rolled over the bottom and sides of the pool, sucking up dirt and other particulates. Vacuumed dirt and debris is conveyed through the skimmer inlet to the pump and then to the sand filter.
Why is my pool vacuum losing suction?
Clogged tubes are one major reason why your pool vacuum lose suction. Vacuum hose connection and length can affect its performance. If your hose length is too short with the size of the swimming pool, then suction performance will be affected. Measure your pool size so does your pool cleaner hose to avoid the problem.
Don’t forget to share this post 
References and Further Readings :
