If simple relighting or replacing the thermocouple or flame sensor does not restore the water heater to good operation, then the problem is more serious and probably requires service from a plumber or appliance technician. Possible causes include a bad gas control valve, or a cracked or damaged burner.
Thereof, Why is my hot water heater not igniting?
If a gas water heater isn’t heating, a common problem is usually that the pilot light has gone out. This may be caused by the gas valve, the gas supply, or—more likely—the thermocouple located next to the pilot light.
Also to know is, Can I manually light my gas water heater? Turn the water temperature dial to Low and the On/Off/Pilot dial to Pilot. Push the On/Off/Pilot dial downward with one hand while lighting the barbecue lighter with the other. Quickly hold the barbecue lighter over the end of the pipe by the burner. The flame should light instantly.
Subsequently, question is, How do you fix a hot water heater Ignitor?
Also, Can you manually light a gas water heater?
Turn the water heat dial to Low and the On/Off/Pilot dial to Pilot. Then, turn the On/Off/Pilot dial downwards and push the igniter button at the same time. Let go of the igniter button, but keep pressing the Pilot dial downward for around 30 seconds. You should hear a “whoosh” sound when the gas is lit.
Can you manually light a water heater with electronic pilot?
* Caution: Most modern water heaters no longer use standing pilots. They use electronic ignition to ignite the gas. Do not attempt to manually light an electronic ignition system. … If the pilot light will not re-light, the problem could be a clogged pilot line or orifice, or gas is not reaching the water heater.
Can I relight the pilot light by myself?
Pilot lights were once standard on all gas furnaces, but newer systems don’t always contain pilot light ignition systems. Instead, some newer furnaces use electronic ignition systems. … Often, homeowners can relight the pilot themselves. Here’s a step-by-step guide on how to relight a gas furnace’s pilot light.
Is it dangerous if hot water heater pilot light goes out?
Not enough combustible air. If your water heater is located in a utility closet or anywhere it is starved for combustible air, the pilot light may go out. This situation could also lead to a build-up of Carbon Monoxide, which can be life threatening.
How do you light a hot water heater without an igniter?
– Take a long lighter to reach the pilot. …
– Remove the plate attached below the dial box. …
– Switch Pilot to OFF.
– Wait for a while, – 5-10 minutes until there won’t be any gas.
– Change the temperature to LOW, and switch to Pilot.
– Push ON/OFF dial down, and simultaneously use the lighter.
How do you light a gas water heater without a Ignitor?
– Take a long lighter to reach the pilot. …
– Remove the plate attached below the dial box. …
– Switch Pilot to OFF.
– Wait for a while, – 5-10 minutes until there won’t be any gas.
– Change the temperature to LOW, and switch to Pilot.
– Push ON/OFF dial down, and simultaneously use the lighter.
Why will my hot water heater not light?
The water heater pilot light is a small flame that ignites the gas burner on your water heater. … If the pilot doesn’t relight, if it goes out right after lighting or if it goes out repeatedly, by far the most common cause is a bad thermocouple.
How do you light a gas water heater with electronic pilot?
– Set the temperature control. to its lowest setting.
– Set the on-off control. to the pilot setting.
– Press the hot water heater. pilot button down and. hold it.
– While looking through the the sight glass slowly press the spark generator until you here it click. You should see a spark.
How does a hot water heater igniter work?
The water heater uses the piezo igniter to light the main gas burner, and when it is pressed down, it releases the electric spark. The spark gap is factory set (0.125″) and should be maintained. … Turn the gas OFF to the water heater and press the piezo igniter. Once pressed, the electrode should release the spark.
Is it dangerous to light a hot water heater?
Before You Strike a Flame Stand near the unit and take a deep breath. Do you smell gas or something like rotten eggs? If so, attempting to light the pilot at this point is extremely dangerous and could cause an explosion. Turn off the gas line to your water heater and wait 1 hour.
How do I get the pilot light back on my boiler?
– Turn the gas to ‘pilot. ‘
– Press and hold the reset switch for one minute and hold a flame to the pilot light at the same time. …
– If all is working as expected, return any casing/doors and turn the gas from ‘pilot’ to ‘on.
What do you do if the pilot light goes out?
– Turn off your appliance at the power switch or thermostat.
– Find the gas valve control knob and turn it to select “pilot.”
– If pilot light controls are sticky, do not apply force or use oil. …
– Press the red button while simultaneously holding a match to the pilot burner.
What do you do when your water heater won’t light?
Don’t forget to share this post 💖
References and Further Readings :