A flashing red function light alerts you when your bottle is empty. Replace the bottle as soon as possible. CAUTION: Do not dispense hot, cool or cold water if the red light is flashing as you could empty the tanks and cause the dispenser to overheat. 1.
Turn all switches to the off position. Unplug the unit. After a few minutes, plug the unit back in, turn the switches back on and give it one hour and recheck the water temperature. If this does not correct the issue, please call our Customer Service Center.
Thereof, How do I reset my water cooler?
To do a reset, drain a few cups of water out of both the hot and cold sides of the water cooler. Then turn the switches in the back of the cooler off. Unplug your water cooler, and leave it unplugged for 24 hours. When you do turn it back on, be sure to turn the back switches on as well.
Also to know is, Why is my water cooler beeping? Why is my water cooler beeping? Some Quench water coolers are equipped with leak detection. The leak detection may have detected moisture in the bottom of the water cooler. This is often caused by an overflowing drip tray, or excess condensation in the water cooler.
Subsequently, question is, How do I clean my Hamilton Beach bottom loading water cooler? IMPORTANT: Set both power switches (on the back of the dispenser) to the OFF position and unplug the water dispenser before cleaning. Use a solution of warm water and baking soda (approximately one tablespoon of baking soda to one quart of water). This will clean and neutralize odors. Then rinse and wipe dry.
Also, How do you troubleshoot a water cooler?
– Remove the water bottle.
– Drain the reservoir entirely by holding down both the cold and hot spigots.
– Place a fresh bottle on the water cooler.
– Watch for leaks. …
– Please place a large X on the faulty bottle and label it a leaker.
How do I reset my water cooler dispenser?
To do a reset, drain a few cups of water out of both the hot and cold sides of the water cooler. Then turn the switches in the back of the cooler off. Unplug your water cooler, and leave it unplugged for 24 hours. When you do turn it back on, be sure to turn the back switches on as well.
How do I fix my bottom load water cooler?
Why does my water cooler make noise?
If your water cooler makes noise, it could be from hot water overheating, copper coils vibrating, loose panels or screws, air trapped in the lines, or a clogged vent pipe. Caution: Always remember to UNPLUG the water cooler from power and ground yourself when performing troubleshooting or repairing a water cooler.
How do you reset a Primo water dispenser?
My bottom loading water dispenser is not producing hot water. Turn all switches to the off position. Unplug the unit. After a few minutes, plug the unit back in, turn the switches back on and give it one hour and recheck the water temperature.
How do you adjust the temperature on a primo water cooler?
– Move the Primo water dispenser away from the wall, being careful not to tip or spill the water bottle.
– Locate the flat, brass-colored screw on the back of the water dispenser.
– Turn the screw slightly clockwise for colder water or counterclockwise for warmer water. …
– Check the temperature of the water.
How do you adjust the temperature on a water cooler?
How do I fix my water dispenser not cooling?
How does a bottom load water cooler work?
Bottom Loading Water Dispensers The dispenser comes with a cap and hose that fit over the top of the bottle and extend down to the bottom. All you have to do is peel the seal of the top of the bottle and fit the cap over it. Then slide the bottle into the base of the water cooler and you’re done.
Why is my Primo water dispenser red light blinking?
A flashing red function light alerts you when your bottle is empty. Replace the bottle as soon as possible. CAUTION: Do not dispense hot, cool or cold water if the red light is flashing as you could empty the tanks and cause the dispenser to overheat. 1.
How do you self clean a Primo water dispenser?
Visit www.PrimoWater.com to find Primo Water at a store near you. green control to OFF to stop cooling. Self-Cleaning Switch – Located on back by itself. Press IN, hold for 5 seconds and release to activate the cleaning cycle.
How do I adjust the temperature on my whirlpool water cooler?
– Press the TEMPERATURE button. The hot water icon and. …
– Press the ADJUST up arrow and down arrow buttons, to set. the hot water temperature. …
– Press the TEMP button again. The cold water icon and. …
– Press the ADJUST up arrow and down arrow buttons, to set. the cold water temperature. …
– Press the TEMPERATURE button again to exit.
Why is my water cooler not cold?
Water cooler troubleshooting Very often if your water cooler is not working, the problem can be traced to the power supply. So as a first step, check that it is properly plugged in at the wall and the mains power is turned on. If it is switched on but not dispensing water, the next step is to check your water supply.
Don’t forget to share this post 💖
References and Further Readings :