similarly, Why is my Frigidaire Gallery refrigerator freezing everything?

If the air damper is faulty or stuck open, then you will have too much cold air entering the fresh food compartment. This can result in the food in the fridge portion of the refrigerator to freeze. … Inspect the air damper and if you find it to be faulty, replace it.

on the other hand, How do I force my Frigidaire ice maker to cycle?

How to Force an Ice Maker to Cycle

1. Open the freezer door to remove the ice bin from below the ice maker.
2. Empty the ice from the bin. …
3. Press the ice maker toggle switch to the “On” setting if it is not already activated.
4. Pop off the front cover of the ice maker with the tip of a flat-blade screwdriver.

also, How do you reset a Frigidaire stand up freezer? Member

1. Unplug Freezer for at least 20 minutes.
2. Plug Freezer back in.
3. Hold Alarm Reset Button for 3 seconds.
4. Quickly, press the DOWN ARROW 3 times.
5. Press the UP ARROW 1 time.
6. Select Temperature you would like for your freezer.

What do you do when your ice maker stops working?

Fix: Start by making sure all electrical connections are properly seated. Slide the refrigerator out from the wall, turn off the water supply valve and disconnect it from power. Locate the quick release plug on the back wall inside the freezer. Unplug the connection it and reconnect it to ensure it’s fully connected.

What is causing my fridge to freeze up?

Frost builds up primarily due to the interaction from letting warm air into the fridge freezer. To avoid this, try not to open the door too often, and don’t leave the doors open for very long. The cold air inside your appliance needs to be properly isolated from the outside temperature.

What is the coldest setting on a Frigidaire refrigerator?

The coldest setting is 7 which is about -10F, the number _1_ is the warmest setting. You can set freezer to _4_, the recommended setting.

Where is the Frigidaire ice maker reset button?

The reset button is located on the front of the ice maker, underneath the motor housing, past the front cover. Press and hold the reset button (you’ll need to apply some pressure here) until you hear the ice tray motor begin to torque, then release.

How do you unfreeze a Frigidaire ice maker?

How do you defrost a Frigidaire ice maker?

1. Unplug the refrigerator and remove any ice from the ice maker and the ice tray.
2. Locate the water refill tube that runs to the ice maker.
3. Turn a hair dryer on low speed and point it at the refill tube to defrost.

Why is my new Frigidaire freezer not freezing?

The most common cause for this condition is a problem with the defrost system. The defrost heater turns on several times throughout the day to melt away any frost that may have accumulated on the freezer evaporator coils.

Does a freezer have a reset button?

Most don’t automatically reset. If the appliance has a reset button, it should just need to be held in for 30 seconds to correct the fridge.

How do you reset the compressor on a Frigidaire refrigerator?

Locate the refrigerator power cord on the back of the appliance. Disconnect the power cord from the wall outlet. Turn both the fridge and freezer controls to “Off” or “0” inside the fridge. Adjust the fridge and freezer controls to the desired setting.

What can cause a Frigidaire ice maker to stop working?

Frigidaire Ice Maker Not Working

• Cause 1: Ice Maker Switch Turned Off. …
• Cause 2: Freezer Temperature is Above 10 Degrees F (-12 C) …
• Cause 3: Faulty Door Seal. …
• Cause 4: Clogged Water Filter. …
• Cause 5: Low Water Pressure. …
• Cause 6: Faulty Door Switch. …
• Cause 7: Faulty Water Inlet Valve. …
• Cause 8: Faulty Ice Maker Assembly.

Where is the reset button on Frigidaire ice maker?

The reset button is located on the front of the ice maker, underneath the motor housing, past the front cover. Press and hold the reset button (you’ll need to apply some pressure here) until you hear the ice tray motor begin to torque, then release.

How do I unfreeze my ice maker?

You could unplug the refrigerator to thaw the lines, but this requires emptying the contents of the refrigerator. A more convenient option is to use a hairdryer to quickly thaw the lines. Confirm first that your ice maker is not malfunctioning. Pour about 1/2 cup of water into the ice maker’s water reservoir.

How do I stop ice build up in my fridge?

Tips for Reducing Ice Buildup in Fridge

1. Keep the doors closed as much as possible. …
2. Ensure your fridge is level so the doors stay closed.
3. Check the hinges and gaskets. …
4. Let hot dishes cool before you store them to reduce moisture in the fridge.

How do I clean the coils on my fridge?

How to clean refrigerator coils: A step-by-step guide

1. Step 1: Gently pull the refrigerator away from the wall. …
2. Step 2: Unplug the refrigerator. …
3. Step 3: Locate the coils. …
4. Step 4: Start vacuuming. …
5. Step 5: Use the paintbrush to remove any stubborn bits of dirt. …
6. Step 6: Vacuum up all the dirt you knocked loose onto the floor.

Is ice build up in freezer bad?

The buildup of ice in your commercial freezer might look cool, but it’s not. There are a whole host of reasons, but simply put, frost and icing are bad because they cost money. … Frost and icing can also cause freezer burn. This ultimately damages the integrity of food.

Why does my Frigidaire refrigerator not get cold?

A Frigidaire refrigerator not cooling properly may have a dirty or damaged seal, allowing cold air to escape and warm air to enter. Assess the door seal for dirt and debris or signs of damage like rips or tears.

Is 5 or 1 colder on a fridge?

On every fridge the rules for the coldest settings are always the following: The numbers on the fridge’s temperature dial indicate refrigerant power. The higher the number goes the colder the fridge will maintain. Setting it to 5 will make your fridge the coldest.

What number should my Frigidaire refrigerator be set at 1 9?

If you are not sure what to set it to, then set it somewhere in the middle. If the dial is numbered 1 to 5 set it on 3, if the dial is numbered 1 to 9, then set at 4. USUALLY the higher the number on the temp control dial, the colder the temperature your refrigerator will get.

How do I reset my Frigidaire ice maker?

I called the company this evening and they told me to reset the unit: 1. Hold/press the power button for 10 seconds; unplug and drain. Wait 30 minutes, plug back in, refill, and see if it works. If it does not work, call them back, they are open 24-hours.

Why isn’t my Frigidaire ice maker working?

The ice maker switch might be defective. It is also possible that the icemaker switch got turned off by accident. Check the switch to ensure that it is turned on. If the icemaker switch is turned on, but the ice maker still isn’t working, use a multimeter to test the switch for continuity.

Why does my Frigidaire ice maker freeze up?

A refrigerator ice maker that freezes up can be caused by a frozen ice maker fill tube, faulty water inlet valve, too low freezer temperature setting, or a water filter that needs replacing. First, locate the water supply to your ice maker and turn off the water supply via the shut off valve.

Don’t forget to share the post !

The post Does a Frigidaire freezer have a reset button? appeared first on True DIY : Your Number One Source for everything DIY, Crafts and handmade.

similarly, Is there a reset button on a Frigidaire?

To factory reset your Frigidaire refrigerator, press the default settings button on the display panel. All your customized refrigerator settings such as alarm tones, temperature display, and temperature will return to factory default settings.

on the other hand, Does a refrigerator have a reset button?

Most don’t automatically reset. If the appliance has a reset button, it should just need to be held in for 30 seconds to correct the fridge. Some refrigerators, including Maytag and Amana, need to have the lock button and the reset or auto buttons held at the same time to reset the fridge.

also, How do I force my Frigidaire ice maker to cycle? How to Force an Ice Maker to Cycle

1. Open the freezer door to remove the ice bin from below the ice maker.
2. Empty the ice from the bin. …
3. Press the ice maker toggle switch to the “On” setting if it is not already activated.
4. Pop off the front cover of the ice maker with the tip of a flat-blade screwdriver.

How do I run a diagnostic on my Frigidaire refrigerator?

How to Enter the Diagnostic Mode on a Frigidaire Refrigerator

1. Press and hold the “Freezer Temperature UP” and the “Freezer Temperature DOWN” buttons at the same time.
2. Release and press the buttons together twice more within five seconds to enter the diagnostic mode to test the Frigidaire.

What is the first thing to check when a refrigerator stops working?

The first thing to check is the breaker (in your home’s electrical service panel) of the circuit serving the fridge.

Should I unplug my fridge if it’s not working?

It’s a good idea to unplug it completely if you can, as you don’t want to be standing in water while working around the appliance. If it’s a freezer/refrigerator combination, the refrigerator food should be fine for 1-2 hours as long as you leave the door closed.

How long does it take for a refrigerator to reset?

On average, refrigerators take around 12 hours to cool down. However, the cooling time ranges from 2 hours up to 24, depending on the brand.

Where is the Frigidaire ice maker reset button?

The reset button is located on the front of the ice maker, underneath the motor housing, past the front cover. Press and hold the reset button (you’ll need to apply some pressure here) until you hear the ice tray motor begin to torque, then release.

How do I reset my Frigidaire ice maker?

Some Frigidaire refrigerators have an an on/off button for the icemaker located on the front control panel. To reset the icemaker press this switch until the LED turns red, wait a few minutes, then press and hold it until the LED turns green.

How do you unfreeze a Frigidaire ice maker?

How do you defrost a Frigidaire ice maker?

1. Unplug the refrigerator and remove any ice from the ice maker and the ice tray.
2. Locate the water refill tube that runs to the ice maker.
3. Turn a hair dryer on low speed and point it at the refill tube to defrost.

How do I get my Frigidaire out of diagnostic mode?

In order to exit diagnostic mode on your Frigidaire refrigerator, you will have to completely reset it. To do this, you will need to unplug your refrigerator from the power outlet for at least 30 seconds. Once you plug it back in, your refrigerator will have exited diagnostic mode.

What number should my Frigidaire refrigerator be set at?

The ideal temperature range is set at 38 °F and it may shut off at 35 °F. Although, if you have meat items in your refrigerator, consider lowering the temperature below the standard value. This range of temperature is very energy saving.

How do you fix a refrigerator that was laying down?

If your refrigerator was on its side for more than 24 hours, let it stand upright for 24 hours before plugging it in. Allowing the fridge to stand in its normal position before plugging it in will give the oil time to flow back into the compressor where it belongs.

What are the signs of a bad refrigerator compressor?

You’ll know that your compressor is bad when it starts making abnormal noises, the compressor overheats or not providing proper cooling, or when the fridge compressor clicks on and off too frequently.

How do I know if my thermostat is bad in my refrigerator?

Here are some signs that your fridge has a faulty thermostat and some troubleshooting tips to help you deal with them.

1. The Refrigerator Is Not Cool Enough.
2. Unusually Cold Refrigerator.
3. Refrigerator Temperature Fluctuation.
4. Sub-Zero Refrigerator Temperature Troubleshooting Tips.
5. Contact Wilshire Refrigeration.

How do I know if my refrigerator compressor is not working?

The best way to tell if something has gone wrong with the compressor is to pull the fridge slightly out from the wall and listen closely. If the motor is running with a slight humming sound but the temperature is above what its normal range should be, then it’s likely there could be a problem with the compressor.

How do you reset a thermostat on a refrigerator?

How do I reset my fridge thermostat?

1. Locate the refrigerator power cord on the back of the appliance.
2. Disconnect the power cord from the wall outlet.
3. Turn both the fridge and freezer controls to “Off” or “0” inside the fridge.
4. Adjust the fridge and freezer controls to the desired setting.

How do I reset my Frigidaire refrigerator after a power outage?

I turned off the breaker to the fridge for 30 secs to try to reset it. If you shut the fridge off, leave it off for several (3-5+) minutes before starting it up again. The internal refrigerant pressures need a chance to equalize before the compressor will start up again without strain on the system.

Can you reset a refrigerator by unplugging it?

Unplug the appliance from the wall socket for 30-45 minutes, then plug it back in. This will reset the device and in some cases it may be enough to completely fix the problem. If a hard reset did not solve the problem, measure the fluid temperature.

Why isn’t my Frigidaire ice maker working?

The ice maker switch might be defective. It is also possible that the icemaker switch got turned off by accident. Check the switch to ensure that it is turned on. If the icemaker switch is turned on, but the ice maker still isn’t working, use a multimeter to test the switch for continuity.

What do you do when your ice maker stops working?

Fix: Start by making sure all electrical connections are properly seated. Slide the refrigerator out from the wall, turn off the water supply valve and disconnect it from power. Locate the quick release plug on the back wall inside the freezer. Unplug the connection it and reconnect it to ensure it’s fully connected.

Why wont my ice maker fill with water?

Water may not be reaching the ice maker due to a frozen line, missing filter, or a closed supply valve. … When there is no filter, or it is clogged, the ice maker does not get water. Make sure that the filter is in place, and if it has not been changed in more than six months, replace it with a new one.

Don’t forget to share the post !

The post Does a Frigidaire refrigerator have a reset button? appeared first on True DIY : Your Number One Source for everything DIY, Crafts and handmade.

similarly, How do I know if my fridge stopped working?

7 Major Warning Signs That Your Refrigerator Is Broken

1. It’s Not Cold Enough. Are you not feeling a chill when you open your fridge? …
2. Your Food is Spoiling Quickly. …
3. There’s Condensation. …
4. Ice Is Building Up in the Freezer. …
5. The Motor is Hot. …
6. It’s Loud. …
7. There’s Water on Your Floor. …
8. Signs Your Refrigerator is Broken.

on the other hand, How do you fix a refrigerator that was laying down?

If your refrigerator was on its side for more than 24 hours, let it stand upright for 24 hours before plugging it in. Allowing the fridge to stand in its normal position before plugging it in will give the oil time to flow back into the compressor where it belongs.

also, Is there a reset switch on a refrigerator? A fridge that is having a hard time keeping your food supplies at the proper temperature for safe consumption may need to be reset. Locate the temperature control switch on the inside of the refrigerator. It is usually in the middle of the back panel or at the top of the refrigerator in a panel above the upper shelf.

How do I know if my thermostat is bad in my refrigerator?

Here are some signs that your fridge has a faulty thermostat and some troubleshooting tips to help you deal with them.

1. The Refrigerator Is Not Cool Enough.
2. Unusually Cold Refrigerator.
3. Refrigerator Temperature Fluctuation.
4. Sub-Zero Refrigerator Temperature Troubleshooting Tips.
5. Contact Wilshire Refrigeration.

How do I know if my fridge thermostat is broken?

Here are some signs that your fridge has a faulty thermostat and some troubleshooting tips to help you deal with them.

1. The Refrigerator Is Not Cool Enough.
2. Unusually Cold Refrigerator.
3. Refrigerator Temperature Fluctuation.
4. Sub-Zero Refrigerator Temperature Troubleshooting Tips.
5. Contact Wilshire Refrigeration.

Should fridge be silent?

Yes, your fridge can be too silent. If your refrigerator isn’t even making so much as a gentle hum, that’s another indication your compressor might be damaged, which will affect your fridge’s cooling capabilities. To troubleshoot, unplug the fridge and plug it back in.

Can a refrigerator go out and the freezer still work?

Refrigerator not cooling but freezer is fine

If your freezer is cold but the refrigerator is warm, it is possible that the parts that cool the refrigerator and freezer are working properly. Instead, the problem may reside in the air that is already getting to the freezer also getting to the refrigerator.

Does it damage a refrigerator to lay it down?

When a refrigerator is horizontal, the oil from the compressor will start to move out and into the coolant lines, clogging them. … Besides this, placing a refrigerator flat on its back is a major no-no: the weight of the fridge can damage its internal parts, even if they’re not exposed.

Can refrigerators be laid down for transport?

Yes, it is generally safe to lay your refrigerator on its side when transporting it. No, it is not ideal. You should let the compressor oil settle down before turning your refrigerator on.

Why would my refrigerator stop cooling and then start working again?

If the thermostat is adjusted incorrectly, the fridge will turn off and turn on again when the temperature increases. The compressors are responsible for providing power for the cooling process. In this case, it is suggested that you lower the thermostat setting to ensure the compressor keeps working properly.

Does a Frigidaire refrigerator have a reset button?

The reset button on your Frigidaire Freezer is likely on the inside. When you’re resetting your Frigidaire freezer, unplug it from the wall for 15 to 20 minutes and then plug it back in. Next, hold down the alarm reset button for three seconds and then press the down arrow three times and the up arrow once.

Should I unplug my fridge if it’s not working?

It’s a good idea to unplug it completely if you can, as you don’t want to be standing in water while working around the appliance. If it’s a freezer/refrigerator combination, the refrigerator food should be fine for 1-2 hours as long as you leave the door closed.

Is there a reset button on a Frigidaire?

To factory reset your Frigidaire refrigerator, press the default settings button on the display panel. All your customized refrigerator settings such as alarm tones, temperature display, and temperature will return to factory default settings.

What are signs of a bad thermostat?

Symptoms of a Failing Car Thermostat

• The temperature gauge reads high and the engine overheats.
• The temperature changes erratically.
• The vehicle’s coolant leaks around the thermostat or under the vehicle.

What happens when refrigerator thermostat goes bad?

Refrigerator Thermostat: Signs of Malfunction

Perhaps your lettuce has frozen patches, and things that should be simply cold are thickening up into semi-frozen slushes. Sometimes, inaccurate thermostats can lead to things like the motor firing up more often than it should, so you’ll hear the fridge more often, too.

How much does it cost to replace a thermostat in a refrigerator?

How much does it cost to fix a thermostat? You will pay between $150 and $200 to have your thermostat replaced. The labor should be around $125, while parts should cost you, on average, about $45.

What are the signs of a bad thermostat?

Symptoms of a Failing Car Thermostat

• The temperature gauge reads high and the engine overheats.
• The temperature changes erratically.
• The vehicle’s coolant leaks around the thermostat or under the vehicle.

How much does it cost to replace a thermostat in a refrigerator?

Fridge Repair Cost

Replacing a thermostat runs on the low end, around $100, compared to repairing the ice maker which costs $300 to $350.

How long should a fridge last?

The average lifespan of a refrigerator

According to a study from the National Association of Home Builders and Bank of America (NYSE: BAC), the typical standard fridge lasts 13 years. For compact refrigerators, often called mini fridges, the lifespan is slightly less at nine years.

Should a refrigerator run all the time?

It is typical for a refrigerator compressor to run anywhere between 4 to 8 hours straight before shutting off. In fact, newer refrigerators are expected to constantly run 80-90 percent of their lifetime.

Can you reset a refrigerator by unplugging it?

Unplug the appliance from the wall socket for 30-45 minutes, then plug it back in. This will reset the device and in some cases it may be enough to completely fix the problem. If a hard reset did not solve the problem, measure the fluid temperature.

How do I know if my evaporator fan motor is bad?

Listen for a squeal or chirp sound. If the evaporator fan motor is going bad, it may still run while making a high pitched sound that may come and go. If you hear that sort of sound, something may be caught in the fan blades or the motor may be dying.

Don’t forget to share the post !

The post What is the first thing to check when refrigerator stops working? appeared first on True DIY : Your Number One Source for everything DIY, Crafts and handmade.

similarly, Is there a fuse on a Frigidaire refrigerator?

where is the fuse panel on my Frigidaire Refrigerator? Hi, welcome to Just Answer. … There is no fuse, see the attached tech sheet. If the power shorted and the refrigerator is dead, the main control was damaged.

on the other hand, How do you fix a refrigerator that was laying down?

If your refrigerator was on its side for more than 24 hours, let it stand upright for 24 hours before plugging it in. Allowing the fridge to stand in its normal position before plugging it in will give the oil time to flow back into the compressor where it belongs.

also, Is there a reset switch on a refrigerator? A fridge that is having a hard time keeping your food supplies at the proper temperature for safe consumption may need to be reset. Locate the temperature control switch on the inside of the refrigerator. It is usually in the middle of the back panel or at the top of the refrigerator in a panel above the upper shelf.

What are the signs of a bad refrigerator compressor?

You’ll know that your compressor is bad when it starts making abnormal noises, the compressor overheats or not providing proper cooling, or when the fridge compressor clicks on and off too frequently.

Do refrigerator ice makers have a fuse?

Appliance Tech – Admin

Give it till overnight and see if it started. If not then you’ll need to check the in-line fuse on the ice maker wire harness. This is how: Ohm the in-line thermal fuse, its located on the wiring harness to the ice maker.

Does a refrigerator have a fuse?

There is only one reason for a refrigerator to blow a fuse in your fuse box. … Fuses are designed to break an internal wire when the circuit draws too much power. Refrigerators, in general, do not have a lot of electronics that could draw enough power to blow a fuse. There is no fuse in your refrigerator.

Where are the fuses located on a Frigidaire?

Insert a putty knife under the control panel, in the corners, to pop up the panel. Lift forward the cabinet of the dryer and pull it off to expose the inside of the unit. Locate the thermal fuse behind the heating element pan, right behind the dryer drum of the machine. The fuse is round with a small wire terminal.

Does it damage a refrigerator to lay it down?

When a refrigerator is horizontal, the oil from the compressor will start to move out and into the coolant lines, clogging them. … Besides this, placing a refrigerator flat on its back is a major no-no: the weight of the fridge can damage its internal parts, even if they’re not exposed.

Can refrigerators be laid down for transport?

Yes, it is generally safe to lay your refrigerator on its side when transporting it. No, it is not ideal. You should let the compressor oil settle down before turning your refrigerator on.

Does laying a fridge down damage it?

If you do lay your fridge down to move it, you can lay it on its front or side, but it’s not recommended that you lay it on its back – the weight of the fridge’s body on its working parts could damage them, even if they’re not exposed.

Does a Frigidaire refrigerator have a reset button?

The reset button on your Frigidaire Freezer is likely on the inside. When you’re resetting your Frigidaire freezer, unplug it from the wall for 15 to 20 minutes and then plug it back in. Next, hold down the alarm reset button for three seconds and then press the down arrow three times and the up arrow once.

Should I unplug my fridge if it’s not working?

It’s a good idea to unplug it completely if you can, as you don’t want to be standing in water while working around the appliance. If it’s a freezer/refrigerator combination, the refrigerator food should be fine for 1-2 hours as long as you leave the door closed.

Is there a reset button on a Frigidaire?

To factory reset your Frigidaire refrigerator, press the default settings button on the display panel. All your customized refrigerator settings such as alarm tones, temperature display, and temperature will return to factory default settings.

Is it worth replacing compressor on refrigerator?

No, it is not worth it to replace the compressor for your fridge. It costs between $200 and $500 for a new compressor, but this does not guarantee the problem will be fixed. … The compressor is responsible for moving refrigerant fluid throughout the coils so that your fridge can cool properly.

Should fridge be silent?

Yes, your fridge can be too silent. If your refrigerator isn’t even making so much as a gentle hum, that’s another indication your compressor might be damaged, which will affect your fridge’s cooling capabilities. To troubleshoot, unplug the fridge and plug it back in.

What happens when a refrigerator compressor goes out?

If the compressor is wearing out in your refrigerator, it will likely cycle more often, or you will notice issues like food spoilage.

Why is my ice maker not getting power?

If your ice maker isn’t producing ice at all or is producing crescents or cubes that are smaller than usual, it’s typically indicative of a clog somewhere along the supply line. Cause: A common cause for a clog is frozen water in the line. Fix: To repair a frozen line, slide the refrigerator and unplug it.

What is a refrigerator thermal fuse?

If the thermal fuse blow off, the refrigerator will stop all the functions(the compressor will not run and the defrost heaters will not heat). A thermal fuse or thermal cutoff is a safety device which open circuits against overheat.

Where is the fuse on a fridge?

The thermal fuse is typically located in one of two places – either inside the refrigerator behind the paneling, or in the rear bottom, next to the compressor. It’s important to remember to unplug your refrigerator unit before attempting to locate your thermal fuse.

What fuse should a fridge have?

Some appliances, such as lamps, televisions, computers, fridges and freezers generally require a 3 amp fuse. However washing machines, dishwashers, microwaves, kettles, toasters and irons usually require 13 amp fuses. Check out our Electrical Socket Calculator to see if you’re overloading electrical sockets at home.

How do you reset a Frigidaire gas control board?

The basic thing you should do is try to perform a hard reset by unplugging the Frigidaire oven, waiting about 20 seconds, and then plugging it back in again. In most cases, this will be enough to reset the control board and get your oven working again.

What happens if you don’t let a fridge settle?

When a refrigerator is placed in a non-standard position (for example on its side), compressor oil can run out of the compressor and up refrigerant lines. So if you don’t stand it upright and wait, the compressor will pump without sufficient oil — not good.

Why do you have to wait 24 hours to plug in a fridge?

This is to allow any oil that may have flowed into the coolant lines to have enough time to return to the compressor and clear the coolant lines. For example, if the unit was on its side for two hours, it must sit upright for at least two hours before you plug it into the wall outlet.

How long before moving a fridge should you unplug it?

When should you turn it off before moving? If you’re moving a fridge or freezer into your new home, it’s best to turn it off 24 hours before. This gives the fridge’s evaporator time to defrost, which reduces the risk of any damage during the move.

Don’t forget to share the post !

The post What is the first thing to check when a refrigerator stops working? appeared first on True DIY : Your Number One Source for everything DIY, Crafts and handmade.