similarly, How do I fix dE error?

A dE error code indicates that the washer door was unable to lock. This can normally be resolved by performing a simple reset on the washing machine.

on the other hand, Why does my LG washer keep filling with water?

If the washer continues to fill with water even when it is not getting power, this indicates that the water inlet valve is defective. If the water inlet valve is defective, replace it. … If the pressure switch fails, the water inlet valve will continue to fill the washer tub with water, causing the washer to overflow.

also, Why is my LG front load washer not draining? Unbalanced Load. One of the most common reasons your LG washer won’t drain often results from an unbalanced load. Washing a large or heavy item can cause it to settle on one side of the washer drum. When this happens your LG washer won’t drain or spin properly and water will be left behind.

How do I reset my washing machine?

To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.

How do I know if my inlet valve is bad?

Signs that point to an inlet valve problem include leaks that fill the dishwasher when not running, the dishwasher filling too slowly when in use, or the dishwasher not filling at all. Leaks that end up outside of the dishwasher also can indicate an inlet valve problem, and this must be addressed immediately.

How do you empty a washing machine full of water?

5 Easy Steps to Get Water Out of Your Washer

1. Step 1: Power It Down and Turn Off the Water Supply. Start by powering down your machine. …
2. Step 2: See If You Can Drain the Drain Hose. …
3. Step 3: Check Out the Drain Pump. …
4. Step 4: Drain the Interior Manually If Needed. …
5. Step 5: Know When to Call a Professional.

How do I fix OE error on my LG top load washer?

Force drain the unit by starting a cycle and pausing it.
…
If you don’t have SPIN ONLY

1. Power the unit ON.
2. Select a cycle.
3. Press START/PAUSE button to START the cycle.
4. Allow a few minutes to pass so the cycle begins.
5. Press the START/PAUSE button to PAUSE the cycle.
6. Run an empty wash cycle to see if issue occurs again.

How do you know if your washing machine drain hose is clogged?

Observe the washing machine as it pumps water into the hoses and up into the standpipe. If you see water back up and out of the standpipe, your washer’s drain is most likely the issue. The amount of time it takes for the standpipe to fill up and overflow helps you diagnose where the clog is located.

Why does my washer stop after it fills with water?

To verify that the valve is at fault, unplug the washer when the symptom occurs. If the washer continues to fill, then the water inlet valve is defective. If the washer stops filling, then the problem is related to the electrical circuit that controls the valve.

Why is my washer not getting water?

The very first thing to do is to check that your water supply is turned on. The switch is usually located under your kitchen sink. If the supply is turned on, then check the inlet hose carefully to ensure that there are no kinks which could be restricting or preventing the water supply from reaching your machine.

Where is the drain pump on my washing machine?

The drain pump may be located behind removable panels in either the front or back of the washing machine, even underneath the appliance, requiring you to tip the machine forward to access it (consult your owner’s manual for instructions). You’ll see a drain hose and inlet hose connected to it with spring clamps.

Can you clean a water inlet valve?

Washing machines pull in water from your home’s water supply and mix it with detergent in the laundry tub. … It is a good idea to clean the water inlet valve on your washing machine every year or so.

Can you repair water inlet valve?

There is little that you can do to repair the valve itself, but you can clean the two inlet ports to restore full water flow. You can also test the valve to determine whether it has failed. Replacing a bad valve is a simple job and must be done with parts and procedures that are specific to your washing machine model.

How much does it cost to replace a washing machine water inlet valve?

A washing machine inlet valve replacement costs $75 to $125.

Why does my washer still have water in it?

While the double tub inside your washer may still be properly operating, there could be sitting water inside. … When your drain hose is clogged, it will prevent water draining from the outer tub. This issue can be caused when something that was in the inner tub has slipped through to create a clog or obstruction.

How often should you drain your washing machine?

Washing machines can be breeding grounds for salmonella and other germs. When you wash items in hot water, your machine is being cleaned as well, but once a month, you should still run an empty load with hot water and about a cup of distilled white vinegar to sanitize the basin and wipe out any lingering germs.

Does Spin Cycle drain water?

It removes the water from the tub during the spin cycle. The washer pump forces water from the bottom of the machine into the drain hose. The drain hose loops to the top of the machine, and then down to the drain, enabling the tub to fill. When the water reaches the bend in the hose, it goes out of the drain.

How do I know if my washing machine drain pump is bad?

You can check by looking for a few signs that a pump is dying or already dead.

1. Start the washer and wait for the washer tub to fill with water. If you do not hear water or hear a motor whirring, the washer motor may be dead.
2. Open the washer lid in mid-cycle. …
3. Wait for the washer to finish its cycle.

Why does my LG washing machine keep draining?

If your Washer fills with water but constantly drains out, there are a few possible reasons. Most likely the water coming into the washer through the Water Inlet Valve could be siphoned out to the drain pump and out the drain hose because of an issue with the pump or plumbing.

How do you unclog a washing machine drain pipe?

To unclog a clogged drain, first fill a bucket with boiling water and a pack of baking soda. Remove the drain pipe from your washing machine and slowly pour the water into the drain using a funnel. Wait a few minutes and test if it keeps draining if you pour water into it.

What is the best drain cleaner for washing machine drain?

Here is a List of the Best Drain Cleaners

• Instant Power Hair and Grease Drain Opener. …
• Thrift Drain Cleaner. …
• Roebic K-87 Soap, Grease, and Paper Digester. …
• FlexiSnake Drain Weasel Sink Snake. …
• Omont Drain Snake Clog Remover. …
• Vastar Drain Snake Hair Drain Clog Remover. …
• FlexiSnake Drain Millipede Hair Clog Tool.

How do I know if my washing machine drain hose is clogged?

An easy way to check that the drain hose is clear is to blow air through it. If nothing is obstructing the drain tube, the problem is most likely at the washing machine pump. If the hose is worn or badly kinked, replacing the hose may improve the ability of the machine to pump water.

How do I know if my washing machine drain is clogged?

Test the drain by pouring water into it, if it has been backing up. If it’s clogged, you should be able to clear the clog with a plumbing auger.

Don’t forget to share the post !

The post What is IE error on LG washer? appeared first on True DIY : Your Number One Source for everything DIY, Crafts and handmade.

similarly, How do I fix the Sud error on my Maytag washer?

This type of liquid chlorine bleach contains a thickening agent that may create excess suds in washers. If this is the case, run the washer empty, using regular liquid bleach products, or clean with affresh^® washer cleaner before running another load.

on the other hand, How do you stop water from foaming?

While the causes for suds and foam vary, several tips can help you remove suds and keep them from returning.

1. Use Distilled Water. Water from your garden hose or tap is rich in various minerals. …
2. Change the Water Regularly. …
3. Reduce Sun Exposure. …
4. Add a Defoamer Agent.

also, What is the fastest way to get rid of soap suds? Vinegar

1. Wipe the interior of the drum with a clean, dry cloth to remove excess soap residue and bubbles, changing it out as needed.
2. Set the machine to a full load and allow it to fill with water before adding 2 cups of distilled white vinegar.
3. Complete the wash cycle.

What causes excessive suds in washing machine?

The most common cause of excessive foam is using too much detergent or not using a quality detergent like Tide HE Turbo Clean. Tide HE Turbo Clean is specially formulated to deliver the right level of cleaning power when using the recommended dose for your load.

How do I know if my detergent is high efficiency?

Walk down the laundry detergent aisle in any store, and almost every single bottle, box, and the bag has a little symbol on the label: the letters “h” and “e” separated by a red dot on a field of blue surrounded by a white circle swirl. The HE stands for high-efficiency laundry detergent.

Where is the filter on a top loader washing machine?

Top Load Washer – Lint / Pump Filters

1. There are 2 crescent-shaped Fine Mesh plastic lint filters in the bottom of the wash basket under the agitator. …
2. During drain down and spin, the water forces the lint off the bottom of the filters and down the drain.
3. These filters should never require cleaning or replacement.

How do I clear the error code on my Maytag washer?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

What causes foam in a water fountain?

Foam is a common problem in both outdoor and indoor fountains, usually caused by an excess of proteins and other organic compounds left behind by bacteria, plants, or animals. The compounds form a slick layer on the surface, which is then churned up into foam by the splashing water.

Why is there foam in my water fountain?

The foam in the fountain water is generally caused by organic compounds and proteins. The material can be from fish or plants you keep in the pond or plant material or bacteria that was blown into the water. The materials or organic compounds become foamy when they are agitated by the falling water.

Can soap suds clog a drain?

Clogs can either be partial or full, depending on how backed-up soap suds and water eventually behaves in the drain. If soap suds bubble slowly but eventually drain away, the the clog is more than likely partial. If bubbled up soap suds never drains away, then you more than likely have a full clog on your hands.

Does vinegar get rid of soap suds?

Remove dingy soap and detergent residue from clothes by adding 1 cup of white distilled vinegar to the drum of your washer; ½ cup if it’s a front loader. To remove soap residue from large loads, like heavy blankets and towels, add 2 cups of vinegar to the final rinse. Clean your washing machine.

Is dish soap bad for washing machine?

Do NOT put liquid dish soap in your washing machine. … While laundry detergent suds very little, dish soap is designed to get sudsy and foamy, mostly because consumers associate suds and foam with cleanliness.

How do I get rid of excess suds in my washing machine?

How to Remove Excess Detergent

1. If your washer has a cleaning cycle run it to reduce suds. Adding a commercial washer cleaner can also help remove residue.
2. If your washer doesn’t have a cleaning cycle, add ½ cup of white vinegar to the detergent dispenser and run a rinse cycle with an empty washer.

Can too much detergent cause washing machine to leak?

Over Use of Detergent

Rather than a part being damaged or broken, leaks can also occur from adding too much detergent to your washing machine. Oversudsing can happen throughout the entire washing cycle but can be well seen during the emptying stage. Avoid using too much, or high-sudsing, detergent if this happens.

Should you see suds in front load washer?

Seeing lots of bubbles or foam is an easy way to ruin your front load washer. The bubbles will overflow the washer and can destroy electronic systems and void warranties. Plus with lower water levels in the rinse cycle, the detergent will be left in your clothes.

Is liquid or powder detergent better for front load washing machine?

Liquid detergent is better for stain pretreatment or hand washing. … Persil advises using liquid for small or large loads, quick washes in the washer, or hand washing, and recommends powders for large loads, as you can save a little bit of money because t powder is cheaper.

What happens if you don’t use HE detergent in your HE washer?

Only HE laundry detergent should be used in an HE washer because it is a low-sudsing specially formulated detergent. … Using a non-he laundry detergent in an HE washer can create a sudsing problem that can cause detergent bubbles to fill the washer tub and start to overflow from the detergent drawer.

Where is the filter on a GE top loader washing machine?

GE Washer Filters

Washing machine filters can be found along the top rim of the drum, at the end of the drainage hose, under the center agitator’s cover or in the front of the unit behind a small hatch.

Do top-loading washing machines have a filter?

“Top loaders tend to have filters on the valves,” said Amber Peabody, Service Manager at Dunnett Inc. The valve filters sift the water going in and out of the pump and hoses. If you do happen to have a removable filter, consult your owner’s manual on how to properly remove it.

Do washing machines have filters that need to be cleaned?

Do washing machines have filters to clean? Most washing machines will have a filter – you can find it at the front of the washing machine, behind a small hatch. It is essential that you regularly clean this filter, as it will collect everything from lint to hair, coins, tissues and more.

How do I fix the LF on my washing machine?

When “LF” is displayed, there could be an issue with the water flowing into the machine. Check the water inlet hoses to be sure they are not clogged or kinked. You may also need to check the screens on the washer water inlet valve.

What does it mean when your washer says LF?

If F8 E1 or LF (too long to fill) appears in display, the washer is taking too long to fill. … Either the F8E1 or the LF error codes may indicate there is some problem with the water supply going to the washer. Please make sure both inlet hoses are connected and both hot and cold water supplies are turned on.

How do I reset my Maytag front load washer to factory settings?

How to Reset a Maytag Washer

1. Press the “Power/Cancel” button.
2. Push the appropriate button to choose a new cycle.
3. Press “Start/Pause.” You have now reset your Maytag washer.

Don’t forget to share the post !

The post How do you get rid of suds? appeared first on True DIY : Your Number One Source for everything DIY, Crafts and handmade.

similarly, What causes excessive suds in washing machine?

The most common cause of excessive foam is using too much detergent or not using a quality detergent like Tide HE Turbo Clean. Tide HE Turbo Clean is specially formulated to deliver the right level of cleaning power when using the recommended dose for your load.

on the other hand, How do I know if my detergent is high efficiency?

Walk down the laundry detergent aisle in any store, and almost every single bottle, box, and the bag has a little symbol on the label: the letters “h” and “e” separated by a red dot on a field of blue surrounded by a white circle swirl. The HE stands for high-efficiency laundry detergent.

also, Where is the filter on a top loader washing machine? Top Load Washer – Lint / Pump Filters

1. There are 2 crescent-shaped Fine Mesh plastic lint filters in the bottom of the wash basket under the agitator. …
2. During drain down and spin, the water forces the lint off the bottom of the filters and down the drain.
3. These filters should never require cleaning or replacement.

How do I clear the error code on my Maytag washer?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

How do I get rid of excess suds in my washing machine?

How to Remove Excess Detergent

1. If your washer has a cleaning cycle run it to reduce suds. Adding a commercial washer cleaner can also help remove residue.
2. If your washer doesn’t have a cleaning cycle, add ½ cup of white vinegar to the detergent dispenser and run a rinse cycle with an empty washer.

How do you get rid of sink suds?

1. Run your faucet on cold. …
2. Fill a cup with the cold water, and working along the edge of the sink or tub, pour the water slowly. …
3. Work your way in toward the drain slowly, using the edges of the soap foam blob as your guide. …
4. Wipe down the sink or tub with a sponge soaked in warm water once all of the soap foam is gone.

Should you see suds in front load washer?

Seeing lots of bubbles or foam is an easy way to ruin your front load washer. The bubbles will overflow the washer and can destroy electronic systems and void warranties. Plus with lower water levels in the rinse cycle, the detergent will be left in your clothes.

Is liquid or powder detergent better for front load washing machine?

Liquid detergent is better for stain pretreatment or hand washing. … Persil advises using liquid for small or large loads, quick washes in the washer, or hand washing, and recommends powders for large loads, as you can save a little bit of money because t powder is cheaper.

What happens if you don’t use HE detergent in your HE washer?

Only HE laundry detergent should be used in an HE washer because it is a low-sudsing specially formulated detergent. … Using a non-he laundry detergent in an HE washer can create a sudsing problem that can cause detergent bubbles to fill the washer tub and start to overflow from the detergent drawer.

Where is the filter on a GE top loader washing machine?

GE Washer Filters

Washing machine filters can be found along the top rim of the drum, at the end of the drainage hose, under the center agitator’s cover or in the front of the unit behind a small hatch.

Do top-loading washing machines have a filter?

“Top loaders tend to have filters on the valves,” said Amber Peabody, Service Manager at Dunnett Inc. The valve filters sift the water going in and out of the pump and hoses. If you do happen to have a removable filter, consult your owner’s manual on how to properly remove it.

Do washing machines have filters that need to be cleaned?

Do washing machines have filters to clean? Most washing machines will have a filter – you can find it at the front of the washing machine, behind a small hatch. It is essential that you regularly clean this filter, as it will collect everything from lint to hair, coins, tissues and more.

How do I fix the LF on my washing machine?

When “LF” is displayed, there could be an issue with the water flowing into the machine. Check the water inlet hoses to be sure they are not clogged or kinked. You may also need to check the screens on the washer water inlet valve.

What does it mean when your washer says LF?

If F8 E1 or LF (too long to fill) appears in display, the washer is taking too long to fill. … Either the F8E1 or the LF error codes may indicate there is some problem with the water supply going to the washer. Please make sure both inlet hoses are connected and both hot and cold water supplies are turned on.

How do I reset my Maytag front load washer to factory settings?

How to Reset a Maytag Washer

1. Press the “Power/Cancel” button.
2. Push the appropriate button to choose a new cycle.
3. Press “Start/Pause.” You have now reset your Maytag washer.

How do I get suds out of my front loading washer?

Set the machine to a full load and allow it to fill with water before adding 2 cups of distilled white vinegar. Complete the wash cycle. Run a second rinse cycle to remove lingering residue. Repeat these steps if needed until no visible suds remain on clothing or the appliance.

What is high suds detergent?

“Controlled foam powdered laundry detergent for multipurpose institutional, industrial and commercial wash systems. Formulated with a balanced blend of synthetic detergents, fortified with surfactants, brighteners, anti-redeposition agents to produce a clean and fresh wash.

How do you get rid of Sud?

If you see suds, a quick and simple way to eliminate them is to throw a capful of liquid fabric softener into the wash and run an additional rinse cycle. Vinegar will work as well.

Can soap suds clog a drain?

Clogs can either be partial or full, depending on how backed-up soap suds and water eventually behaves in the drain. If soap suds bubble slowly but eventually drain away, the the clog is more than likely partial. If bubbled up soap suds never drains away, then you more than likely have a full clog on your hands.

Can too much soap clog a drain?

You wouldn’t think soap is capable of clogging your drains, but it definitely will. Bar soap has a habit of re-solidifying in your drains, leading to clumps of it forming into a large, goopy mass over time that will eventually cause a blockage.

What are the disadvantages of a front loading washing machine?

Cons

• Front-loaders are often more expensive than top-loaders.
• You have to bend down to unload the machine.
• The air-tight door invites mold growth. Keeping the door ajar between loads helps to prevent this problem.
• The control panel on the front invites kids to press buttons and change settings.

What should you not put in a washing machine?

15 things you should never put in the washing machine

1. Suits. “Many suits are made of high-quality fabrics that can either shrink or tear, even in a delicate cycle,” says Stapf. …
2. Embellished garments. All that glitters… …
3. Clothes with zippers and buttons. …
4. Swimsuits. …
5. Baby socks. …
6. Excessive detergent. …
7. Bras. …
8. Throw blankets.

Which detergent is best for LG front load washing machine?

The new Ariel Matic is specially designed to give you great results for fully automatic washing machines and is available for both top loading and front loading washing machines. It also comes recommended by LG as the best detergents for washing machines.

Which detergent is best for front load washing machine?

For example, your front load washing machine will work by agitating your clothes at high speeds to help remove the dirt. So hand washing detergent or even a top load washing machine detergent will produce too many suds. So it’s best to get the right Ariel Matic for your machine.

Don’t forget to share the post !

The post How do I fix the Sud error on my Maytag washer? appeared first on True DIY : Your Number One Source for everything DIY, Crafts and handmade.

similarly, Why are suds coming out of my washing machine?

The most common causes of too much foam are too much washing detergent or not using a quality detergent like Ariel. Ariel is specially formulated to deliver the right level of cleaning power, with added ingredients that ensure the levels of suds are also controlled to an optimum level.

on the other hand, How do I fix the OE error on my LG washer?

OE can be triggered by a kinked drain hose or a clogged drain pump filter.

1. Check for kinked drain hose. Check behind the washer to ensure that the drain hose is not kinked or clogged. …
2. Test the drain pump. …
3. Do you hear the humming sound? …
4. Clean drain pump filter. …
5. Run tub clean cycle. …
6. Request Repair.

also, Why is my LG washer not getting water? Common solutions for: LG Washer fills slowly or will not fill at all. The water inlet valve opens to allow water to enter the washing machine. … If the water pressure is adequate, try cleaning the screens inside the water inlet valve hose connection ports. If the washer still fills slowly, replace the water inlet valve.

What kills foam?

Vinegar and salt are both great at reducing the foam caused by detergents for hand washing. Salt reduces the surface tension of the water which inhibits the production of suds. The dishwasher should then be forced through a rinse cycle.

How do you get rid of sink suds?

1. Run your faucet on cold. …
2. Fill a cup with the cold water, and working along the edge of the sink or tub, pour the water slowly. …
3. Work your way in toward the drain slowly, using the edges of the soap foam blob as your guide. …
4. Wipe down the sink or tub with a sponge soaked in warm water once all of the soap foam is gone.

How do I know if my washing machine drain pump is bad?

You can check by looking for a few signs that a pump is dying or already dead.

1. Start the washer and wait for the washer tub to fill with water. If you do not hear water or hear a motor whirring, the washer motor may be dead.
2. Open the washer lid in mid-cycle. …
3. Wait for the washer to finish its cycle.

How do I test my LG washing machine drain pump?

Test the drain pump.

1. Press POWER to turn the washer ON.
2. Press the SPIN SPEED key until HIGH is selected.
3. Press the START/PAUSE button to start the SPIN ONLY cycle.
4. Listen to hear a humming sound which indicates that the drain pump motor has started working.

Is my LG washer using enough water?

Your LG washer is designed to use as little water as possible for efficiency. This is done by slowly filling the washer while checking the saturation level of the clothing. Once the clothing is completely wet, a sensor goes off indicating that the washer has enough water.

How do I stop foaming in water?

Common strategies for foaming control include: Reduction of SRT (Sludge Retention Time, similar to mean cell retention time, often used in wastewater treatment operation) to wash out filamentous bacteria; removal of hydrophobic substances and substrate that could enhance foaming or favor the growth of filamentous …

Does high pH cause hot tub foam?

A Bad Chemical Balance Can Cause Hot Tub Foam

Water with a pH greater than 7.8 parts per million has too much pH, while hot tub water with alkalinity higher than 120 pm is too alkaline. Either problem can lead to cloudiness.

How do you get rid of Sud?

If you see suds, a quick and simple way to eliminate them is to throw a capful of liquid fabric softener into the wash and run an additional rinse cycle. Vinegar will work as well.

Can soap suds clog a drain?

Clogs can either be partial or full, depending on how backed-up soap suds and water eventually behaves in the drain. If soap suds bubble slowly but eventually drain away, the the clog is more than likely partial. If bubbled up soap suds never drains away, then you more than likely have a full clog on your hands.

Can too much soap clog a drain?

You wouldn’t think soap is capable of clogging your drains, but it definitely will. Bar soap has a habit of re-solidifying in your drains, leading to clumps of it forming into a large, goopy mass over time that will eventually cause a blockage.

How long does LG washer last?

The average life expectancy for washers and dryers is between 10 and 15 years. Front loaders are very efficient.

Where is the drain pump on LG washer?

The pump on an LG machine is located in the front of the washer on the bottom left near the floor. The LG front-load washer has an accessible drain filter to help keep lint and objects out of the pump.

What washer uses the least amount of water?

Front load washing machines use less water than top loaders

That’s because they’re able to wash clothes by picking them up and dropping them into the wash water repeatedly, unlike top loaders which wash clothes by having them float around in water.

Why does my LG washer take so long to wash?

The amount of detergent is too much which is forming too much foam that will increase cycle time. But, HE Washers Have Longer Wash Cycles. … Since they use less water, they take longer to wash and rinse clothes to get them clean.

Why do new washers use so little water?

Because they use less water, they use less energy to heat the water — just 20 to 50% of the energy used by traditional washers, making them energy efficient. Less water and energy = environmentally friendly and budget friendly. They spin faster to remove more water from clothes, so clothes need less time in the dryer.

How do you control foam?

To restrict or reduce bubbles and foams many chemical facilities add chemical additives called defoamers, such as alcohols or glycols, to their mixtures. However, these can affect chemical product purity, and often need to be filtered out in a later process, taking more time and added costs.

Why is my septic tank foaming?

Phosphates that pass through the septic system due to improper design can enter surface water, causing very high growth rates of algae. … Surfactants typically cause foaming or suds in water.

How do you reduce excessive foam in milk processing?

When using a top-entering agitator to add powders into a foamy liquid, position the mixer blade off-center to decrease the vortex. Reducing the size of the vortex will minimize foaming and reduce the amount of air incorporated into the batch.

Why am I getting foam in my hot tub?

Hot Tub foam is caused by the water being “full” or “old” and turning the jets of your hot tub on when the water is like this will cause foam to appear on the waters surface. There are several products that, if added to the water, can cause foam.

What causes yellow foam in hot tub?

Spa water that is tinted clear yellow usually indicates a high bromine residual and a low pH. This is fairly common with bromine spa systems, because the bromine can discolor the Phenol Red used to test pH. … When the pH and total alkalinity are properly adjusted, the yellow discoloration should go away.

Don’t forget to share the post !

The post How do I fix Internet Explorer error on my LG washer? appeared first on True DIY : Your Number One Source for everything DIY, Crafts and handmade.