– Remove the two screws on the top-rear corners of the dryer with a Phillips-head screwdriver. …
– Remove the four screws on the back of the control panel with the screwdriver. …
– Remove the two screws at either of the upper-front corners of the front panel with the screwdriver.
Thereof, How do I open my dryer to clean it?
To clean inside the dryer, unplug it and turn off the gas, then open either the top or the front. The procedure is the same for gas and electric dryers. For dryers with a top lint filter and a solid front panel, remove the lint filter and take out the two screws on the side of the lint filter opening.
Also to know is, Why is my Samsung dryer not starting? The fuse is located on the blower housing or at the dryer’s heat source such as the heating element on electric dryers or at the burner on gas models. … If the dryer does not respond or make any noise, the start switch could be at fault. Use a multimeter to test the start switch for continuity.
Subsequently, question is, How do you remove the front panel of a dryer?
Also, Is there a way to clean a dryer?
Use a long flexible dryer lint brush (available at home centers) and a gentle twisting motion to clean the cavity. Vacuum the brush clean, then repeat the process until you can’t remove any more lint. Or, try using the crevice attachment on your vacuum cleaner to clean out the lint.
How do you remove the front panel of a Maytag dryer?
– Unplug the Maytag clothes dryer from the power source. …
– Pull the bottom of the front panel toward you until the clips on the top of the panel release.
– Carefully disengage the wires from the door switch and set the door aside.
– Unplug the Maytag clothes dryer from the power source. …
– Lift the door slightly and pull back.
How do I open my dryer?
How dO I run a diagnostic on my Samsung dryer?
– Make sure the drum is empty and then close the door.
– Press POWER to turn the dryer on and within 5 seconds, press and hold Adjust Time Up + Dry Level until InS or In appears on the display.
– Press and hold START/PAUSE to start the Vent Blockage test which lasts for approximately 2 minutes.
How do you diagnose a dryer problem?
Is there a way to reset a Samsung dryer?
Resetting your dryer is easy. Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the dryer (usually 1 to 5 minutes at most), and then power it up again. That’s it. That’s all it takes to reset.
How do you remove the front of a dryer?
– Unplug the dryer from the wall prior to servicing.
– Slide a putty knife under the front left and right sides of the control panel to release the spring clips. …
– Remove the two screws at the rear of the top panel and then slide the top panel forward and lift if off of the dryer.
How do you open the front of a dryer?
– Unplug the dryer from the wall prior to servicing.
– Slide a putty knife under the front left and right sides of the control panel to release the spring clips. …
– Remove the two screws at the rear of the top panel and then slide the top panel forward and lift if off of the dryer.
How do I open my front load dryer?
How do I clean the lint out of my front load dryer?
– Locate the exterior exhaust hood to the dryer, if possible. …
– Unplug the dryer from the power source. …
– Unscrew the clamp that holds the dryer vent hose to the exhaust duct in the wall. …
– Remove the lint screen filter from the front of the dryer. …
– Insert the vent brush into the vent pipe in the wall.
How do you fix a squeaky Samsung dryer?
How do you take the front of a dryer off?
– Unplug the dryer from the wall prior to servicing.
– Slide a putty knife under the front left and right sides of the control panel to release the spring clips. …
– Remove the two screws at the rear of the top panel and then slide the top panel forward and lift if off of the dryer.
What would cause my dryer not to start?
If your dryer won’t start when you push the start button, the most likely causes are a lack of power, a defective door switch, a blown thermal fuse or a bad start switch. … Check your power cord and the house circuit breaker. Try resetting the breaker to make sure it’s not tripped.
Don’t forget to share this post 
References and Further Readings :