How long a PT 4X4 lasts in the ground is dependent on where you live, your environment. Basically, It won’t last more than half a decade. I’ve seen treated posts that were under a roof last 40 years. Untreated wood lasts one year, max.
Thereof, How do you put a straight line in a fence post?
– Mark both ends of one side of the fence with a tape measure and dig a hole on each mark with a post-hole digger for the anchor post. …
– Drive screws into the two anchor posts, about 6 inches from the ground and allow the heads to protrude about one-half inch.
Also to know is, How do you line up a fence post?
Subsequently, question is, How do you layout fence posts?
Also, How do you anchor a fence post without concrete?
Backfilling the fence post hole with gravel is another common alternative to using cement. Start with a hole about the size of the one you’d dig if you were using cement, insert a third of the post’s length into the hole, and then fill with crushed gravel, tamping every five inches until flush.
How do you secure a 4×4 post in the ground?
– Dig post hole so diameter of the hole is 3 times the width of the post (i.e., the hole for a 4” wood post should be about 12 inches wide). …
– Add about 6 inches of QUIKRETE All-Purpose Gravel into the bottom of the hole. …
– Set the post into the hole and attach 2×4 braces to adjacent sides of the post.
How do you anchor a fence post to concrete?
How do you secure a fence post without concrete?
– Find a concrete surface and lightly tamp your digging iron against it. …
– Remove the turf and topsoil from the site of the post. …
– Dig the hole putting the displaced earth onto the tarp. …
– Pour 4 inches of gravel into the hole.
– Place the post in the hole. …
– Add another 2 inches of gravel around the base of the post.
How do you set a 4×4 fence post?
Is concrete necessary for fence posts?
Concrete is the most secure material for setting fence posts, especially if you have sandy soil. Gravel may be okay with dense, clay-heavy soil, but in looser soil, concrete is the only thing that will truly keep your fence posts stuck in place.
How do you secure a 4×4 post without digging?
Instead of digging, the flanges are driven into the ground by hammering on a bit inserted into the bracket with a sledge or a jackhammer. The post is then inserted into the bracket and held in place with screws. Post anchors make it easy to install a fence post without cement or other types of anchoring.
How do you secure posts in the ground?
Set the post into the hole and attach 2×4 braces to adjacent sides of the post. Use a level to position the post perfectly vertical. Fill the hole with Fast-Setting Concrete up to 3 to 4 inches below ground level. Pour about a gallon of water per 50 lb bag into the hole and allow the water to saturate the concrete mix.
How do you stiffen a fence post?
– Take out adjacent fence construction. …
– Cut or buy a few tapered (top to bottom) surveyor stakes about 24 inches long. …
– Drive a stake into the ground next to the post or next to the concrete. …
– Pull the stake.
– Fill the hole with water and level the post. …
– Add dry premixed concrete to the top of the hole. …
– Wait half an hour.
How do you level a fence post?
Instead of filling in the top of the hole with soil that could hold moisture at the base of your fence post, add a little more concrete to divert rainwater away from the post and protect it from rot at ground level. You’ll need just a bucket or wheelbarrow to mix the concrete and a trowel to smooth it in place.
Do you need to use concrete with fence posts?
Concrete is the most secure material for setting fence posts, especially if you have sandy soil. Gravel may be okay with dense, clay-heavy soil, but in looser soil, concrete is the only thing that will truly keep your fence posts stuck in place.
How do you level a post?
– Attach the post level to the material you are working with using the rubber band. …
– When the material is plumb with the ground, the bubbles in the horizontal vials will be centered inside the lines.
– When the material is level, the bubble inside the vertical vial will be centered inside the lines.
How do you support a post to concrete?
Attach angled 2 x 4 braces to two adjacent sides of the post using one screw for each brace. Drive a stake into the ground near the lower end of each brace. 4. Use a level to position the post plumb (perfectly vertical), checking on two adjacent sides with the level, then fasten the braces to the stakes.
Don’t forget to share this post 
References and Further Readings :
