Duet Washer Diagnostic Test Mode
Pick any three buttons on the Duet washer control except power, start, or cancel. Now do the key dance within eight seconds… Button 1, Button 2, Button 3, Button 1, Button 2, Button 3, Button 1, Button 2, Button 3 (You are pressing 9 buttons in 8 seconds so it needs to be pretty quick.)
similarly, How do I reset my Whirlpool Duet dryer F01?
The Whirlpool Duet Dryer F01 error may be able to be fixed with a simple reset of the main control. Unplug the dryer for 1 minute and plug it back in this will reset the control if the error persists after that you will need to check the dryer thermal fuse. The fuse is located on top of the blower wheel housing.
on the other hand, How do you reset a Whirlpool Duet front load washer?
Unplug the washer for 30 seconds to attempt to reset the Duet washer control. if your fill hoses have a flood stop check valve turn the water off, disconnect the hoses and run a little water into a bucket. Then reconnect the hoses to your washer and do a Duet Washer Quick Diagnostic Test.
also, Is there a reset button on a Whirlpool front load washer? How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
What does error code F01 mean on a Whirlpool Duet dryer?
Troubleshooting and Repair – F01 Error Code – WED8300SW0. The F01 error code means the primary control unit in the dryer has failed and will have to be replaced. The control that needs replacing is the electronic control board not the user interface and/or control panel.
How do I reset my Whirlpool front load dryer?
If your Whirlpool dryer displays a “PF” error code, indicating a recent power failure, the dryer will need to be reset and restarted. This is done by pressing “Start” for a few seconds to restart the dryer. If the dryer does not restart automatically, select a new cycle and any options then press “Start” to begin.
How do you reset a Whirlpool dryer?
Whirlpool Tumble Dryer Reset Procedure
- Turn on the tumble dryer main power.
- Within 10 seconds turn the program selector from off to teh 6 o’clock postion, pointing straight down.
- Push the “Start” button three times.
- Turn the program selector to the “one” position which should be the CW or airing program.
How do you clear the error code on a Whirlpool front load washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do I reset my Whirlpool washer after a power outage?
How do I reset my Whirlpool washer after a power outage?
- Unplug the washer for 1 minute from the electrical outlet.
- Plug the washer back in and lift and lower the lid 6 times within a 12 second period. …
- The motor has now been reset and is ready for you to start a cycle.
Why is my Whirlpool washing machine not turning on?
One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home’s main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.
How do I clear the error code on my Whirlpool washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
What does F1 mean on a front load dryer?
The “F1” error means that the dryer’s thermistor failed. The dryer is reading the thermistor as “open” and the actual part has shorted out. The thermistor is used to read and control temperatures within the dryer. Without the part, the dryer will not operate.
How do I fix F1 error on my Whirlpool dryer?
When the Whirlpool Cabrio displays an F1 error, this means the the control board is having difficulty communicating with the motor. To fix your F1 error, you can first try to unplug your washing machine for 15 minutes and then plug it back in. If this doesn’t work, you will need to replace the control board.
Where is the dryer reset button?
Many dryers are equipped with a reset button on the control panel. If the motor won’t run, let the dryer cool for about ten minutes.
Is there a reset button on a whirlpool?
How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
How do you fix a Whirlpool dryer that won’t turn on?
Whirlpool Dryer Not Starting? This Could Be the Problem
- Make sure the dryer is correctly plugged into the proper electrical outlet.
- Check for tripped breakers or blown fuses. If needed, reset any tripped breakers and replace blown fuses.
- Avoid using an extension cord.
Where is reset button on a dryer?
Many dryers are equipped with a reset button on the control panel. If the motor won’t run, let the dryer cool for about ten minutes.
How do I reset my thermal fuse?
- Step 1: Locate the Fuse. Study the owner’s manual for the location of the thermal fuse. …
- Step 2: Cut Power to the Dryer. …
- Step 3: Disassemble as Needed. …
- Step 4: Disconnect the Thermal Fuse. …
- Step 5: Conduct a Continuity Test. …
- Step 6: Purchase a Replacement. …
- Step 7: Replace the Fuse. …
- Step 8: Reassemble the Dryer and Test It.
How do I clear the error on my Whirlpool Duet washer?
Press the “Pause/Cancel” button on the control panel twice to clear the error. Contact a certified repair technician if pressing the “Pause/Cancel” button does not clear the error, as this indicates that a component has failed in the washing machine or dryer.
How do I reset my front load washer?
How to reset the washing machine:
- Press POWER to turn the washer off.
- Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
- With the power disabled, press and hold the START/PAUSE button for 5 seconds.
- Plug the washer back in, or turn the circuit breaker back on.
How do you reset a Whirlpool dryer?
If your Whirlpool dryer displays a “PF” error code, indicating a recent power failure, the dryer will need to be reset and restarted. This is done by pressing “Start” for a few seconds to restart the dryer. If the dryer does not restart automatically, select a new cycle and any options then press “Start” to begin.
How do you reset a washing machine after a power outage?
Turn the machine on with dry hands. If it still won’t start, unplug it or turn the circuit breaker off, then back on until the breaker firmly clicks in place and plug the machine into the outlet. Push the restart button. Some machines may require you set the knob to a specific setting for the reset feature to work.
Why is my washing machine not turning on?
Power Source
Make sure the machine is tightly plugged in. Next, check for a tripped circuit breaker. Reset the breaker and try to start the washer. If neither is at fault, you may have a damaged power cord.
Don’t forget to share the post !
