When the Washing Machine is displaying E1 in the panel, it is indicating an error in the water supply. The appliance is not detecting that the unit is filling with water.
If F9 E1 (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water. The drain may extend more than 4.5″ (114 mm) into standpipe. … If not, the washer could siphon (fills and drains at the same time).
Thereof, How do I fix e1 error on my washing machine?
– Drain the water from the machine by lowering the drain hose below the water level to a bowl or your machine may have a drain hose near the filter.
– Place a towel under the filter and pull the filter out to remove any debris that may have gathered.
Also to know is, What does the code SD mean on a Maytag washer? excessive detergent suds
Subsequently, question is, How do you fix a SD code on a Maytag washer? Maytag acknowledges that error codes like “Sd” sometimes appear by mistake. Push the “Pause/Cancel” twice or “Power” button once to remove the code from the screen and try using the washer again. If the code returns, unplug the washer for 60 seconds and try the cycle again before calling for assistance.
Also, How do you reset the code on a Maytag washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do you fix a SD on a washing machine?
Simply put, too much detergent was used and an excessive amount of suds or foam was produced. Adding an additional rinse cycle without adding any more detergent might fix this problem. Sometimes the machine will automatically detects this problem and add a pause and additional rinse cycle in order to break up the suds.
How do you read a Maytag washer code?
How do I fix error code 5d?
Reset error code 5d, because, in some instances, it occurs due to a failure. To solve the problem correctly, you need to press PAUSE / CANCEL 2 times or POWER 1 time and then start washing. Stop the washer and take out too voluminous, soft, and fluffy things. Then continue the cycle.
How do you clear the error code on a Maytag washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
Why is my Maytag washer says e01 f09?
So you’re exactly right, E01 F09 means you have a drain issue. There is a drain catch inside the washer that you will want to access and clean if you’re getting this drain error. To access the drain catch, tip the machine backwards and lean it against the wall at a 45 degree angle or so.
What is a 5d error code?
Did you receive an Sd (may appear as 5d) or Sud Error Code? If Sd or Sud (excess suds) appears in display, you have excessive suds in washer. The washer is running a suds reduction routine. Allow the washer to continue.
How do I reset my Maytag front load washer?
– Press the “Power/Cancel” button.
– Push the appropriate button to choose a new cycle.
– Press “Start/Pause.” You have now reset your Maytag washer.
How do I reset my Maytag washer?
– Unplug the washer for 1 minute from the electrical outlet.
– Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
– The motor has now been reset and is ready for you to start a cycle.
What does it mean when your washer says 5d?
suds lock
How do you troubleshoot a Maytag washer?
– Washer won’t spin.
– Washer is making loud noise.
– Washer won’t agitate.
– Washer won’t drain.
– Washer vibrating or shaking.
– Washer fills slowly or will not fill at all.
– Washer leaking water.
– Washer won’t start.
How do you reset the lid lock on a Maytag washer?
2 – Press and hold the “END OF CYCLE / CYCLE SIGNAL” button(s) for 20 seconds and this should reset the washer and clear the flashing light. Important Tip: Never change the washing machine settings once the washer has already started any wash cycle, as this can cause the lid lock light to flash.
How do I fix error code 5d on Maytag washer?
Maytag acknowledges that error codes like “Sd” sometimes appear by mistake. Push the “Pause/Cancel” twice or “Power” button once to remove the code from the screen and try using the washer again. If the code returns, unplug the washer for 60 seconds and try the cycle again before calling for assistance.
Don’t forget to share this post 💖
References and Further Readings :
