The F5 error code indicates that the Central Control Unit (main machine control board) detects a temperature sensor resistance that is out of the normal range.
Likewise, How do I clear the error code on my Whirlpool washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
Also, What is F5 error code?
An F5 error code indicates that the fan on the outdoor or indoor unit has been running at a very low speed for a set period of time. This occurs when either the controller on the board or the fan malfunctions.
Moreover, What does F5 and E3 mean on a washing machine?
The F5 E3 alert indicates there is issue with the lid lock. … Remove any objects from the lid and clear any obstructions. Touch POWER to exit cycle, then touch POWER again to release lid. If this is unsuccessful, reboot the machine by unplugging the washer and wait two minutes before plugging the machine back in.
What does F5 and E2 mean on a washing machine?
The F5 E2 alert indicates the washer can’t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area. Also verify there are no clothing items in the way.
Is there a way to reset a Whirlpool washer?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
How do you reset a front load washer?
How to reset the washing machine:
- Press POWER to turn the washer off.
- Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
- With the power disabled, press and hold the START/PAUSE button for 5 seconds.
- Plug the washer back in, or turn the circuit breaker back on.
Is there a reset button on a washing machine?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
How do I fix E3 error on my washing machine?
0C, 0E, E3 code appears on the washer screen. In this case, you need to drain water and remove the laundry. Then, run the rinse mode to clean the drum. Next, start the technique to make sure that the OC error has disappeared.
How do I fix error code E3?
This could be due to a wiring mistake, faulty fan assembly, faulty fan motor, or a faulty control board. Before touching or maneuvering the wires, be sure to turn off the power from the disconnect box for the outdoor unit, or from the breaker box for the indoor unit.
How do I fix E3 error on my washing machine?
5 Answers
- Unplug The Washing Machine: Unplug the washer for 2-3 minutes. …
- Check Wire Connections On Drive Motor: One fairly common issue that causes the 3E error code is connection problems. …
- Check Wire Connections On Control Board: …
- Check Hall Sensor:
How do I fix F5 E3 error on Maytag washer?
F5 E3 Error Code
- Power unit down by turning off the circuit breaker or unplugging for one (1) minute.
- Power unit up by reconnecting power.
- Restart a new cycle.
- Monitor the washer for one (1) minute to ensure the error code does not display again.
How do I fix E3 error on my Whirlpool washer?
If you receive an E3 Error code, your washer may be unbalanced. This could be caused by the washer being too tightly packed, or clothing not distributed evenly. This will usually occur during the spin cycle. Stop the spin cycle.
What does E2 mean on a Kenmore washer?
Dryers , Kenmore , Washers. 1 Answer from this member: The E2 error message indicates the control has detected a shorted thermistor. Most likely replacing the thermistor will fix this problem.
How do you reset the F5 code on a Whirlpool washer?
When using hot water in a Whirlpool washer, you may encounter the “F5” error code on the appliance. To finish the laundry load, reset the washer, wash in cold water and then fix the error to use hot water again.
How do I reset my Whirlpool front load washer?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
Why is my washer stuck on wash?
If your top load washing machine (or some older front load washers) is stuck on one continuous cycle and will not advance and forward to the next wash cycle, then most likely the washer timer is faulty and needs replacement. The timer on your washing machine controls all aspects of the wash, spin, and rinse cycles.
How do I know if my washing machine control board is bad?
A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining.
Why did my front load washer stop spinning?
Front-load washer tubs spin thanks to a drive belt that runs off of the motor. A loose, frayed, or torn belt could be why your washer won’t spin. Overloading your washing machine can cause the belt to loosen or become worn out. Inspect the drive belt closely.
Why won’t my washing machine finish its cycle?
Drainage Problems
If the washing machine doesn’t drain properly then something blocking the pump could have caused the washer to stop mid cycle. … General overheating is again a possible cause for your washer to stop mid-cycle, many washing machines have built-in sensors.
How do I fix E1 error on my washing machine?
If the error code E1 appears, there is a problem draining the water. First, check the washing machine’s filter. Place a bucket under the rubber pipe and then remove the plug. While it’s draining, remove the filter and rinse it under the faucet.
How do I reset my washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
What does E3 mean on Bosch washing machine?
Fault Code 3 – Door not closed.
This fault means that the door isn’t closed properly, or there is a problem with the door latching mechanism, or the door interlock. For more help on fixing this fault see our guide on my washing machine won’t turn on.