An F9 error code on a General Electric (GE) oven indicates that the oven’s electronic control system has detected a problem with the automatic door lock. … The malfunction may be a jammed door lock mechanism, a pinched or broken wire, a faulty lock switch or a fault in the control board itself.
similarly, How do you unlock a GE Profile oven door?
GE Profile ovens are only meant to be locked during a cleaning cycle. If the oven lock activates while something bakes, press “clear/off” and wait for the oven to cool completely. The door should unlock.
on the other hand, How do I clear F9 code?
How to Remove the F9 Code From Maytag
- Hold on the “Start/Stop” button for 10 seconds. This will end the beeping. …
- Open the oven door and check the door latch. …
- Spray a little WD-40 onto a washcloth and scrub off any rust or debris on the latch. …
- Press the oven door shut gently. …
- Test the oven.
also, How do you clear a LOC on a GE oven? The lockout setting is activated by pushing and holding the “lock controls” button for three seconds. Deactivating the lockout is also accomplished by holding down the “lock controls” button for three seconds.
What does F4 mean on a GE oven?
F4 fault code usually means that the oven sensor needs to be replaced. Fault codes are programmed in all electronic ranges. These codes help GE Appliances Factory Service technicians quickly diagnose issues.
How do you unlock a GE oven after self cleaning?
If The Oven Door Will Not Unlock After Self-Cleaning:
- Try the following to unlock the door:
- Disconnect power to range for 30 seconds. Reconnect power and see if the door will unlatch.
- If the door does not unlatch and you do not have food in the oven, set the oven to Self-Clean for 1-2 hours.
How do I turn off the control lock on my stove?
After connecting the appliance to an electrical power supply or after a power failure, the control panel will be locked. An indicator light above the key icon will be on. To unlock the control panel, press and hold CONTROL LOCK for 3 seconds. The indicator light will turn off, and the appliance is ready for use.
Why does stove say f9e0?
This code will most often indicate that the appliance is wired incorrectly at the home electrical supply, or at the hard wire connection. If your oven was installed recently (within approximately 3 months), contact a qualified electrician to verify the electrical supply.
Where is the oven door switch?
The door switch is a small cylindrical part set into the upper right or left corner of the oven door aperture with wires through the back.
How do I fix the F9 code on my Frigidaire oven?
Turn off your oven and then unplug it. Wait several minutes before you plug the appliance in once again and turn it on. This should reset the system and prompt you to reprogram the electronic control panel.
How do you unlock oven controls?
Every brand of oven is slightly different, but many have a process that will reset the oven’s computer panel and trigger the oven door to unlock. It may be something like pressing the “Clock” button and the “Clear/Off” button at the same time for 10 seconds, or holding down on the “Child Lock” button for 30 seconds.
How do you fix F3 error on GE oven?
Clear/Off. The oven control panel has a “Clear/Off” button, which is normally used to cancel an oven setting. When an error code, such as the F3 code, appears on the control panel screen, it might just be a temporary glitch. To determine if this is the case, push and hold the “Clear/Off” button for two to five seconds.
What does F4 code mean?
The “F4” fault code indicates shorted temperature sensor probe or a shorted temperature sensor circuit. The sensor and sensor circuit will need to be checked and tested for being shorted. … It should measure approximately 15 ohms at room temperature.
Where is the temperature sensor on a GE oven?
The temperature sensor, also known as the oven temperature sensor assembly is usually found in the back of the oven. The function of the oven temperature sensor assembly is to measure the temperature inside your oven while it is on and send the temperature back up to the electronic control, which adjusts as necessary.
How do I unlock my oven after cleaning the cycle?
Take your wire hook, place it between the oven door and the rest of the oven, place it over the latch, and pull it (the latch is usually in the top center of the oven door). This should release the lock, and you’ll be able to open the oven door.
How do I unlock my oven after self-cleaning?
Unlocking the Oven After Self-Cleaning. Unplug the oven for 5 minutes, plug it back in, and press “Clear/Off”. This can sometimes prompt the oven’s computer to reset and release the lock button.
How do I reset my self-cleaning oven?
The oven’s computer can be reset by changing the circuit breaker that controls the oven. Press the self-cleaning button again if the oven doesn’t open. If the door is unlocked after 30 seconds, cancel the cycle.
How do you unlock a GE range control?
To activate: Press the Lock Controls pad for three seconds to lock or unlock the control. Cancel/Off is always active, even when the control is locked.
How do I unlock my GE Profile dishwasher?
To LOCK the dishwasher control, touch and hold the HEATEd dry pad for 3 seconds. The light below the HEATEd dry pad will turn on. To UNLOCK the dishwasher control, touch and hold the HEATEd dry pad for 3 seconds. The lOCK light will turn off.
How do I fix F9E0?
F9E0:
- Press CANCEL>CANCEL>START to enter the Diagnostics Mode and verify the failure. …
- Unplug range or disconnect power.
- Verify that the house power supply provides 240 VAC between L1 and L2, and 120 VAC between L1 and N and L2 and N. …
- Verify that the electric supply is wired correctly at the range terminal block.
How do I fix my oven F9?
Reset the Oven
Sometimes, the F9 error code is the result of an electrical fault that has magnetized the circuitry. Resetting the oven by disconnecting the power for five minutes will demagnetize the circuitry and resolve the F9 error.
How do you reset the code on a Whirlpool stove?
Plug the oven power cord back in or turn ON circuit breaker. Press CANCEL on the display. If fault code comes back after 1 minute then replace the keypad. If F2 E5 persists then replace the electronic oven control.
How do you turn off the oven light?
To turn the light on while the door is closed, touch Oven Light on the control panel. The oven light can be turned off with the door open by pressing Oven Light on the control panel. When turning on the upper or lower oven light of an M, L, or E Series Double Wall Oven, both lights should not turn on.
What is an oven door switch?
The oven door switch detects whether the oven door is closed and helps control the oven light. Unless you have the oven light control set to keep the oven light on constantly, the door switch shuts off the light when you close the door.
How do you replace an oven switch?
How to Replace Your Oven Selector Switch
- Have the Switch Tested. First things first, be sure it’s your selector switch that needs replacing. …
- Order a Replacement Switch. …
- Prepare to Repair. …
- Access the Control Panel. …
- Remove the Old Switch. …
- Install the New Selector Switch. …
- Reassemble the Oven. …
- Test Your Repair.
Don’t forget to share the post !