Many dryers are equipped with a reset button on the control panel. If the motor won’t run, let the dryer cool for about ten minutes.
similarly, How do I reset my Whirlpool Duet dryer F01?
The Whirlpool Duet Dryer F01 error may be able to be fixed with a simple reset of the main control. Unplug the dryer for 1 minute and plug it back in this will reset the control if the error persists after that you will need to check the dryer thermal fuse. The fuse is located on top of the blower wheel housing.
on the other hand, How do I reset my thermal fuse?
- Step 1: Locate the Fuse. Study the owner’s manual for the location of the thermal fuse. …
- Step 2: Cut Power to the Dryer. …
- Step 3: Disassemble as Needed. …
- Step 4: Disconnect the Thermal Fuse. …
- Step 5: Conduct a Continuity Test. …
- Step 6: Purchase a Replacement. …
- Step 7: Replace the Fuse. …
- Step 8: Reassemble the Dryer and Test It.
also, Do all tumble dryers have a reset button? Not all tumble dryers have re-set buttons, so if it stops heating it is most likely to be because the thermostat or TOC (Thermal Overload Cutout) has tripped due to overheating. Thermostat’s are usually the size of a 5p and can be accessed by removing the back panel.
How do I know if my thermal fuse is blown?
How to tell if a thermal fuse has blown? To test if your thermal fuse has blown, touch the right side of your multimeter lead to the right side of the fuse, and repeat with the left multimeter lead. If the multimeter needle fails to move, this indicates the thermal fuse has blown.
What does error code F01 mean?
The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes.
What does error code F01 mean on a Whirlpool Duet dryer?
Troubleshooting and Repair – F01 Error Code – WED8300SW0. The F01 error code means the primary control unit in the dryer has failed and will have to be replaced. The control that needs replacing is the electronic control board not the user interface and/or control panel.
How do you reset the code on a Whirlpool Duet dryer?
How do I reset my Whirlpool Duet steam dryer?
- Inspect household fuses or breakers.
- Close the dryer door firmly.
- Press and hold the “Start” button for five seconds.
- Check the display on the dryer for error codes.
- Press the “Start” button and hold for several seconds to restart the dryer if “PF” appears on the display.
Why is my dryer running but not heating?
Common reasons for an electric or gas dryer not heating are a tripped circuit breaker, clogged vent, and no gas flow. Other potential reasons include a faulty thermal fuse and broken heating element. If you gather your tools and follow this guide, you may be able to solve basic dryer heating problems on your own.
Is it safe to bypass a thermal fuse?
Bypassing a Dryer Thermal Fuse
Operating a dryer with a bypassed thermal fuse is both unnecessary and unsafe, so a bypass should only be done long enough to troubleshoot a potential problem. Even short usage without a thermal fuse in place could result in irreparable damage to the appliance or injury to yourself.
Why is the dryer blowing cold air?
One of the most common reasons your tumble dryer decides to blow out cold air instead of hot is, rather ironically, because it has overheated. … If your tumble dryer does not have a reset button it is likely you will need to replace your thermostat and thermal overload cut-out (TOC).
Why is my tumble dryer drum not going round?
A broken drive belt is the most common reason a dryer won’t spin. … A working belt should provide some resistance, so if the drum turns very easily and loosely, the belt is probably broken. Unplug your dryer and remove the lid so you can inspect the belt to confirm that it’s broken.
How do you tell if a thermal fuse is blown without a multimeter?
Testing By Bypassing The Fuse
If you do not have a multimeter, you can also test whether or not the fuse is working by bypassing the fuse itself. Simply detach the wires from the fuse, wire them together using a jumper wire and attempt to operate the dryer.
When I press the start button on my dryer nothing happens?
If your dryer won’t start when you push the start button, the most likely causes are a lack of power, a defective door switch, a blown thermal fuse or a bad start switch. … If it doesn’t turn on, it’s likely that the dryer has no power. Check your power cord and the house circuit breaker.
Why does dryer say F1?
The “F1” error means that the dryer’s thermistor failed. The dryer is reading the thermistor as “open” and the actual part has shorted out. The thermistor is used to read and control temperatures within the dryer. Without the part, the dryer will not operate.
What does F01 mean on a battery charger?
F01 INTERNAL SHORTED CELL BATTERY – Cannot be charged. Have battery checked by certified auto service center. OR. EXCESSIVE LOAD ON BATTERY WHILE CHARGING – Check load. F02 BAD BATTERY CONNECTION – Check battery connection.
How do you test a dryer control board?
How to test your dryer’s rotary switch: Unplug your dryer and remove the control console panel on the top of your dryer to locate the rotary switch. Set your multi-meter to the Rx1 setting and place the probes on the switch’s terminals. You should receive a reading of infinity.
How do you troubleshoot a Whirlpool Duet dryer?
How to Troubleshoot a Whirlpool Duet Electric Dryer
- Inspect household fuses or breakers. …
- Close the dryer door firmly. …
- Press and hold the “Start” button for five seconds. …
- Check the display on the dryer for error codes.
How do you reset the code on a Whirlpool washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do I fix a dryer that is not heating?
This is the most common cause of a dryer not heating. To check if your venting is clogged, start a timed dry on high heat. Go to the exhaust vent outside and use your hand to verify that the air is very warm and exiting at a decent flow. If there’s little airflow, your venting likely needs to be cleaned or replaced.
How do you know if the heating element is bad in my dryer?
If the heating element isn’t working properly, the dryer will still spin and the cycle will complete, but it won’t get hot enough to help dry the clothes. Heating elements can naturally wear out over time, but overloading the dryer, not cleaning the lint screen and poor ventilation can all speed up that process.
What causes a thermal fuse to fail?
Answer: Clogged or restricted exhaust vent air flow is the most frequent cause of a thermal fuse blowing. Check the lint screen for lint or a build-up of debris that could be inhibiting air flow through the dryer. Pro Tip: when it comes to those thermal fuses, is they’re designed to open/fail if they get too hot.
Will the dryer run if the thermal fuse is blown?
A gas dryer will run but won’t heat if its thermal fuse blows because the dryer overheated (usually because the vent is clogged, so check the vent path).
Don’t forget to share the post !
