In GE dryers, the thermal fuse–sometimes called a safety thermostat–is located behind the drum on the inside of the dryer. To access the thermal fuse you will need to open the dryer from the top. Though it may sound a bit daunting, opening the top of the dryer to reveal its inner workings is surprisingly simple.
Table of Contents
READ ALSO
Likewise, Why is my dryer knob not working?
If the dial has been turned too much, it may stop turning all together. Dirt and grime are also culprits in a dial that no longer turns. Use a spray lubricant to loosen the dial if grime and dirt are stuck inside the dial mechanism. If the dial is in fact broken, you must purchase and install a replacement knob.
Also, How do I know if the thermal fuse is blown?
How to tell if a thermal fuse has blown? To test if your thermal fuse has blown, touch the right side of your multimeter lead to the right side of the fuse, and repeat with the left multimeter lead. If the multimeter needle fails to move, this indicates the thermal fuse has blown.
Moreover, Do GE dryers have a reset button?
Many dryers are equipped with a reset button on the control panel. If the motor won’t run, let the dryer cool for about ten minutes.
How do you reattach a dryer knob?
Pull the dryer knob off the timer shaft. Some dryer manufacturers have a small c-clip securing the knob to the timer shaft. Grab the clip behind the dryer knob with a pair of needle-nose pliers. Pull the clip up until it disengages from the shaft, and pull the knob off the unit.
How do you start a dryer knob?
Many dryers allow you to turn the timer knob either way. Whether you turn it clockwise or counterclockwise, you will eventually get to the setting that you want to get to. Once the dryer knob is at the correct setting, press the start button or push in the knob, depending on your dryer, to get the dryer to turn on.
How do you reset a GE dryer?
How do you reset a GE dryer? Turn the dryer off, then on again to reset it. Or you can press the reset button on the dryer plug.
When I press the start button on my dryer nothing happens?
If your dryer won’t start when you push the start button, the most likely causes are a lack of power, a defective door switch, a blown thermal fuse or a bad start switch. … If it doesn’t turn on, it’s likely that the dryer has no power. Check your power cord and the house circuit breaker.
Is it safe to run a dryer without a thermal fuse?
Operating a dryer with a bypassed thermal fuse is both unnecessary and unsafe, so a bypass should only be done long enough to troubleshoot a potential problem. Even short usage without a thermal fuse in place could result in irreparable damage to the appliance or injury to yourself.
Where is the dryer reset button?
Many dryers are equipped with a reset button on the control panel. If the motor won’t run, let the dryer cool for about ten minutes.
How long do GE dryers last?
The average electric dryer should last about 14 years. The average gas dryer is a little less durable, lasting about 13 years. If you’re approaching your dryer’s average lifespan, but a $40 repair will last you another year or two, it may be best to repair it for now.
What causes a GE dryer not to start?
If your dryer will not run or start, check the following: Make sure the dryer plug is pushed completely into the wall outlet. Check that the dryer door is closed tightly. Make sure that the cycle selection button is positioned on the desired temperature, fabric and drying time.
Which way does a dryer drum turn?
The normal rotation of the dryer drum in this model is counter clockwise. A broken drive belt is the most common reason a dryer won’t spin. A working belt should provide some resistance, so if the drum turns very easily and loosely, the belt is probably broken.
Do GE electric dryers have a reset button?
Many dryers are equipped with a reset button on the control panel. If the motor won’t run, let the dryer cool for about ten minutes.
Why is my GE dryer not turning on?
If your dryer will not run or start, check the following: Make sure the dryer plug is pushed completely into the wall outlet. Check that the dryer door is closed tightly. Make sure that the cycle selection button is positioned on the desired temperature, fabric and drying time.
Can a dryer be fixed?
Most dryer problems can be fixed in an hour with a few basic tools and a continuity tester or multimeter—and you can do the work yourself with these simple instructions.
How do you know if your dryer switch is bad?
As a safety feature, the dryer will not work with an open door. When the switch is broken, it is unable to tell the control panel the door is shut, so the dryer will not turn on. The only way to tell if the switch is faulty is to take it out of the dryer and test it with a multimeter.
Is it worth it to repair dryer?
Is it worth repairing a dryer? Dryer repairs are worth it if the appliance is less than 4 years old and the cost is less than $400. For older dryers and/or costly repairs, replacing your appliance is more cost effective.
What happens when thermal fuse blown on dryer?
A thermal fuse will blow when the temperature gets too high, not when it’s drawing too much current. … When it blows, the dryer stops generating heat. It’s necessary to replace it before the dryer will run again.
Where is the thermal fuse on my dryer?
The thermal fuse will be located somewhere by the exhaust vent on your dryer. You will be able to visually identify it by the two wires connecting to it. Removing the front of the dryer and removing the drum might be easier to access the fuse’s location.
Why did my GE dryer stop working?
When the dryer stops working again due to a replacement fuse or circuit breaker problem in the electrical panel, the terminal block may be at fault. … The blown fuse and breaker trip will have stopped the GE dryer from working.
How can you tell if a dryer heating element is bad?
Inspect the metal wire coil for any breaks in the wire. If the wire is solid and has no breaks in it, the heating element should be good. If the wire has a break in it, the heating element is defective.
Are dryers worth repairing?
Is it worth repairing a dryer? Dryer repairs are worth it if the appliance is less than 4 years old and the cost is less than $400. For older dryers and/or costly repairs, replacing your appliance is more cost effective.
Is it worth fixing a 10 year old dryer?
It’s recommended as a rule of thumb that if your dryer is close to 10 years old, you’re better off replacing it outright, especially if the quote for repairs comes in high.
Is GE or Whirlpool better?
The short answer is yes. Both Whirlpool and GE machines are manufactured in the US to the highest standards of quality and durability. Whirlpool earns the slight edge here, with their machines reporting fewer repair needs or issues. Plus, their repair costs are lower than just about any other brand on the market.
