Turn Lock Feature When enabled, the Keypad Deadbolt (BE365) can be locked from the outside by pressing the Schlage button and then rotating the thumbturn. When disabled, a User Code must be entered before rotating the thumbturn. The Turn Lock feature is enabled by default.
Table of Contents
READ ALSO
First, verify that the batteries are fresh and are installed in the battery holder in the correct orientation. … Remove battery connector. Press and hold the Schlage button on the keypad. While holding the Schlage button, reattach the battery connector.
Thereof, How do you lock a Schlage outside?
Also to know is, How do I change the code on my electronic door lock?
Subsequently, question is, Why does my Schlage Lock unlocks without code? It’s likely that when the unit was installed, the dead bolt was in the locked position. It needs to be installed (two sides joined together) when in the unlocked position. see less The Feb 23rd solution that everyone likes works by turning off the function that lets you lock without entering a code.
Also, How do you override a Schlage Lock?
How do you set a Schlage door lock?
To do this, you’ll first need to open up your smarthome hub app and navigate to where you add a device to the hub to put it in search mode. Next, open your door, extend the deadbolt out so that it’s in the locked position, and then press the Schlage button followed by your programming code plus “0”.
How do you unlock a Schlage Lock?
How do you reset a Schlage Lock?
– Remove the cover plate of the Schlage door lock using a screw driver.
– Remove the battery.
– Press the “Schlage” button.
– Reconnect the battery.
– Press and hold the “Schlage” button for at least 5 seconds. Once complete, the Schlage door lock will be completely reset to the original factory settings.
How do you lock a Schlage door code?
– Press the “Schlage” button and the number “1” button simultaneously to add/change a new entry code.
– Wait for the “Schlage” button to beep and flash three times.
– Enter a new four-digit code, and wait for the “Schlage” button to flash and beep three times.
How do I change my Schlage code without code?
– Enter the existing six-digit code.
– Press the “Schlage” and then the “3” keys.
– When three orange flashes and three beeps occur, enter a new six-digit code.
– When three orange flashed and three beeps occur again, reenter the same new six-digit code.
How do I reset my Schlage keypad?
– Disconnect the batteries. …
– Press and hold the outside Schlage button.
– While holding the outside Schlage button, reconnect the batteries.
– Release the outside Schlage button. …
– To check that the lock was reset, press the outside Schlage button and enter one of the default access codes.
How do you lock a keypad door?
How do I remove a Schlage door code?
To delete a user code on the lock itself, press the Schlage button followed by the programming code, and then hit “2”. After that, enter in the user code that you want to delete twice. If successful, you’ll get a blinking green checkmark and two beeps.
How do I change the 4 digit code on my Schlage keypad?
Press the “Schlage” button and the number “1” button simultaneously to add/change a new entry code. Wait for the “Schlage” button to beep and flash three times. Enter a new four-digit code, and wait for the “Schlage” button to flash and beep three times. Re-enter the same four-digit code to confirm the change.
How do I lock my door from the outside?
Lock the door from the outside. Close the door while you are standing outside. Slide the key into the keyhole and turn it clockwise as far as it will go. If you turn the key far enough, the door should lock. If this does not work, flip the key upside down and try again.
How do you unlock a Schlage keypad lock?
How do you install a Schlage door lock?
Don’t forget to share this post 💖
References and Further Readings :
