To reset a hot tub heater you need to locate the red reset button which will probably be on the heater in the service bay of the hot tub. All you need to do is to press it to reset it and everything should be good to go.
When the temperature of your hot tub changes outside of your range, the light will turn off. When the green light is flashing, this may indicate there is a problem within the temperature sensor. … If the light is still blinking call for service. The bottom BLUE light is an indicator for the power to the hot tub.
Thereof, Why does my hot tub keep blowing fuses?
These fuses may blow due to, loose incoming connections at the spa at the breaker or a bad connection in the holder. … This may be the reason for a blown fuse on the incoming legs of power. Shorts to ground are a real danger which should cause the GFCI breaker to trip most likely before a fuse would blow.
Also to know is, Why is my hot tub light flashing? It also provides a diagnostic function–a blinking power indicator indicates that the heater high limit has tripped, meaning that either the spa water is above its acceptable temperature range, or a malfunction has occurred within the spa (such as low circulation due to clogged filters).
Subsequently, question is, Do hot tubs have a reset button? A spa heater has a high-limit reset button. A spa or hot tub provides a form of personal relaxation known as hydrotherapy. … A spa heater may need to be reset if it has tripped or stopped working. Using the high-limit reset switch and checking all breakers and GFCI outlets can reactivate the spa’s heater.
Also, How do I reset CleverSpa?
The control panel on my CleverSpa® isn’t working/isn’t lighting up? – Reset the hot tub by pressing the ‘Off/Test’ button on the RCD plug. – Wait 10 seconds then press ‘On/Reset’ to turn it back on again.
How do you diagnose a hot tub problem?
– Heater Failure. If the water in your spa isn’t as warm as it should it, it may be an indication of heater failure. …
– Clogged Filter. If water flow is poor and your jets don’t seem to be working as well as they should, you may have a clogged filter. …
– Air Lock. …
– Noisy Pump. …
– Tripped GFCI Breakers.
Is there a reset button on a hot tub pump?
Usually there is a GFCI plug under there that the pump is plugged into and the reset is on that, A red button. Click to see full answer. Similarly, it is asked, how do you reset a Jacuzzi tub? Drain the water using the main control panel and turning the valves below.
Why does my fuse keep blowing?
An overloaded circuit is the most common reason for a circuit breaker tripping. … When a circuit breaker regularly trips or a fuse repeatedly blows, it is a sign that you are making excessive demands on the circuit and need to move some appliances and devices to other circuits.
How do you reset a strong spa?
2. Reset the GFCI breaker by switching the breaker to the full OFF position, wait a moment, then turn the breaker back on. The spa should have power again.
Where is the reset button on a Hot Springs hot tub?
Similarly, where is the reset button on a Hot Springs hot tub? The reset button is located in the equipment compartment. Plug the spa back into the power source.
How do you fix the code on a hot tub?
Check the water level to make sure it is not too low in the spa. Then make sure you do not have an air lock in the spa pump or spa heater causing the code. You can also try removing the spa filter, or replace with a new one to see if the error code goes away while the old filter is removed.
How do you reset the Balboa control panel?
Remove the spa cover and allow water to cool. At 107¡F (approximately 41.7¡C), the spa should automatically reset. If spa does not reset, shut off the power to the spa. Standby Mode has been activated by pressing a button combination on the user panel.
How do you check a hot tub fuse?
– Shut off all power to the spa at the breaker and spa pack.
– Set your Ohm meter to the 1K setting.
– Remove the fuse from the board or fuse housing.
– Place your meter leads on each end of the fuse.
– Compare readings to printed Ohms level.
How do you unlock the Balboa control panel?
Spas using Balboa control systems To unlock the panel, while holding down the “Temperature” button (or the “Up” button if you do not have the “Temperature” button), gently press and release the “Light” button twice.
How do I know if my hot tub circuit board is bad?
If you have no display on your topside control panel, check the cable for damage, following it right to where it plugs in, on the circuit board. Unplug it from the board and the low-speed pump will come on within 1 minute, on both systems. If that doesn’t happen, either the pump or the circuit board is bad.
How do you change the mode on a Balboa hot tub?
Depending on system configuration, mode changing may not be available and will be locked in Standard Mode. Mode is changed by pressing “Temp,” then “Light”. Standard Mode maintains set temperature. will be displayed momentarily when you switch into Standard Mode.
How do I fix my hot tub?
Don’t forget to share this post 
References and Further Readings :