Typically low flame height is caused by one of three things. Either you have low gas pressure at the fireplace or you need to restrict the venting to slow down the draft. 1) It is common to think that the gas pressure is fine when this only one appliance on the line or the meter is turned all the way up.
Thereof, How high should the flames be on a gas fireplace?
Turn the burner on and set the flame height to high. Take a reading. This time, you want to see an ideal reading of 3.5 inches or the pressure rating indicated in the manual. Don’t forget to turn off the burner and the gas and then tighten the screw again.
Also to know is, What do you do when your gas fireplace won’t light?
Subsequently, question is, Why is my gas fireplace not lighting? If gas is coming out of the pilot, but it still won’t light, the spark igniter could be the problem. Alleyne says to look for and clear out any debris between the igniter and thermocouple. Pro Tip: If the pilot is lighting, but not staying lit, it indicates that the thermocouple is worn out, Worthen says.
Also, How much does it cost to replace a gas fireplace?
The average costs related with installing a gas fireplace will include $600 for firebox installation, $750 for the vent pipe, $2,750 for the complete installation and finishing work, and around $150 to $800 for the gas line, depending on how far it’s required to run.
How do I increase the flame size on my gas fireplace?
Turn the key valve counterclockwise as far as it will turn to open the gas line. Start the fire by following your gas fireplace lighting instructions. Turn the gas control knob to high to increase the flames in your fireplace if applicable.
What is the depth of a gas fireplace?
A true linear gas fireplace available at builder pricing, at only 8-3/4″ deep for framing, making it one of the thinnest linears on the market.
What is the minimum depth for a gas fireplace?
16 inches
How do I turn down the flame on my gas fireplace?
– Locate the gas log control knob. …
– Light the gas logs by turning the control knob to the “pilot” setting. …
– Release the control knob and allow the flame to burn for one minute. …
– Locate the switch at the front of the gas logs marked “on.” Move the switch to the “on” setting to ignite the burners below the gas logs.
What is the slimmest gas fireplace?
Heat & Glo®, the leader in fireplace design and innovative technology, is proud to offer REVO™ Series direct vent gas fireplaces. They are among the thinnest fireplaces ever made with 7-inch deep profiles, making it possible to install or hang them just about anywhere.
How much clearance do you need for a gas fireplace?
The top, back, and sides of the fireplace are defined by stand-offs. The minimum clearance to a perpendicular wall extending past the face of the fireplace is one inch (25 mm). The back of the fireplace may be recessed 21 1/2 inches (546 mm) into combustible construction.
How much depth do you need for a gas fireplace?
A true linear gas fireplace available at builder pricing, at only 8-3/4″ deep for framing, making it one of the thinnest linears on the market. Excellent choice for new home construction and renovations.
How do you fix a low flame on a gas fireplace?
Turn the key valve counterclockwise as far as it will turn to open the gas line. Start the fire by following your gas fireplace lighting instructions. Turn the gas control knob to high to increase the flames in your fireplace if applicable.
How do I increase the flame on my gas fireplace?
Turn the key valve counterclockwise as far as it will turn to open the gas line. Start the fire by following your gas fireplace lighting instructions. Turn the gas control knob to high to increase the flames in your fireplace if applicable.
How can I make my gas fireplace quieter?
Ensure your air shutter is properly adjusted according to the Crystal Fire® Plus Burner manual. A properly adjusted air shutter will give the brightest flame and quietest performance. For natural gas the air shutter should be completely closed. For liquid propane, the air shutter should be open between 3/16” and 1/4”.
How do you troubleshoot a gas fireplace?
How do I get my gas fireplace to work?
– Look over the user manual included with your fireplace. …
– Remove your fireplace’s outer cover. …
– Put a fireplace key into the device’s gas valve knob. …
– Hold a long lighter up to the burner and ignite it. …
– Turn the gas key. …
– Replace the fireplace’s outer cover immediately.
Don’t forget to share this post 
References and Further Readings :
