Avoid standing directly behind the chainsaw to avoid injury from kickback. To prevent the trunk from splitting it is advised to make a cut a third of the trunk’s diameter. This cut should be made on the side of the trunk that is going to be exposed to the most compression.
Misjudging where the tension is can cause the chainsaw to become trapped. It is never a good idea to shake your chainsaw while the engine is still running. To do so could cause irreparable damage to your chainsaw and potentially fatal injury to yourself or others.
Thereof, How do I keep my chainsaw from binding?
To stop your chainsaw from getting stuck, make a cut on top of the log or tree that’s preferably one-third of the log’s diameter. Use your chainsaw to cut from the underside until you meet the initial top cut. Always stand on the side when cross-cutting to prevent injury.
Also to know is, How do you unjam a chainsaw?
Subsequently, question is, What causes chainsaw to seize? Seizing is going to be due to a lack of lubrication, and since the fuel mix is the lube; either the carb was set too lean, or the carb was functioning improperly due to what ethanol does to these carbs when they sit unused, or the fuel mix was not 50:1.
Also, How do you fix a pinched chainsaw bar?
To open pinched rails, mount the bar in a vice and gently tap on the bent rail with a hammer and punch. A flat-blade screwdriver is another tool that can be useful for prying open bent bar rails. Once you’ve got the pinch worked out, test your repair by placing the chain back in the groove.
How do you ground a log on a chainsaw?
– Start up the chainsaw (running at slow speed)
– Position over the pre-marked points on the trunk.
– Saw 3/4 of the trunk.
– Repeat for every pre-marked section.
– Rotate the trunk 180 degrees.
– Finish the cut by sawing through the opposite side.
What causes a chainsaw to stall?
An engine stalls when it’s getting too much or not enough fuel from the carburetor. Stihl chainsaw carburetors usually have three adjustment screws: one each for idle, low speed and high speed. … If the saw is stalling when you pull the throttle trigger or it doesn’t reach its full power, adjust the high-speed (H) screw.
Why does my chainsaw stop cutting?
The most common cause of a chainsaw that won’t cut properly is a dull cutting chain. Try sharpening or replacing the chain. The chain may not have the proper amount of tension. … If the chain is too tight, the chain may not rotate at the proper speed, causing the chain not to cut properly.
How do you cut up a fallen tree with a chainsaw?
Why does my chainsaw blade keep falling off?
A damaged bar or chain may cause the chain to come loose from the bar and can be very dangerous when operating the machine. … If the chain itself has broken teeth or does not fit back into the rails once it has come off, it will likely need to be replaced.
Why is my chainsaw getting stuck?
Misjudging where the tension is can cause the chainsaw to become trapped. It is never a good idea to shake your chainsaw while the engine is still running. To do so could cause irreparable damage to your chainsaw and potentially fatal injury to yourself or others.
Why does my chainsaw smoke when cutting?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
How often should you flip the bar on a chainsaw?
Just depends on what kind of wood I am cutting, etc…. So after cutting, say, 2 cord or so, flip your bar. Every 4 or 5 cord, clean your rails……you’ll be amazed at the difference it’ll make.
Why is my electric chainsaw smoking?
It isn’t normal for a chainsaw to smoke, but if it does happen it can be the result of the chainsaw overheating, the fuel mix containing too much oil, or the chain either not being sharp enough or not getting enough lubrication. In short, a smoking chainsaw is a sure sign that something isn’t right.
Do you flip the bar on a chainsaw?
Chainsaw bars don’t wear evenly. … Every chainsaw bar has been designed to be mounted right-side up or upside down. The reason for this is that it allows the user to extend the life of his chainsaw bar by 50%. Flipping the bar will give the heavily-used areas some relief from wear and tear.
How do I know if my chainsaw needs a new bar?
How do you unstick a chainsaw?
Don’t forget to share this post 💖
References and Further Readings :